Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

TI505 (CP1434) Comm with S7-300 /S7-400 (IE/PB Link Moduled)

Created by: Lex at: 9/13/2013 4:45 PM (7 Replies)

Rating (0)

Thanks 0

8 Entries

9/13/2013 4:45 PM	Rate (0)
Lex Advanced Member Joined: 12/12/2006 Last visit: 1/27/2020 Posts: 19 Rating: (0)	I have a project that need to communicate. Between TI505 (CP1434) and S7-300/S7-400 via IE / PB Link,. It is still uncertain whether there is any way that I can. I do not know how I have some advice. Thank you. Alex

Suggestion To thank Quote Answer

9/13/2013 5:02 PM	Rate (0)
billwest Gold Expert Joined: 6/20/2007 Last visit: 8/4/2018 Posts: 510 Rating: (113)	If your 505 CPU has a Profibus Connector you can use the DP DPcoupler. You can transfer 244 bytes perPLC scan. billwest
	Bill West Principal Sales Application Engineer Siemens Industry, Inc. Digital Factory Division
Suggestion To thank Quote Answer

9/13/2013 8:20 PM	Rate (0)
Lex Advanced Member Joined: 12/12/2006 Last visit: 1/27/2020 Posts: 19 Rating: (0)	For the TI505 it. I used CPU TI545-1102. And CP1434H1. I used for the S7-300 CPU317-2DP. And 6GK1 411-5AA0 (Ethernet / Profibus Gateway). I have attached a Config. Please advice me. Ragards, Alex Attachment Config.gif (112 Downloads)

Suggestion To thank Quote Answer

9/14/2013 12:31 AM	Rate (0)
billwest Gold Expert Joined: 6/20/2007 Last visit: 8/4/2018 Posts: 510 Rating: (113)	The Diagram doesn't make use of the IE PB, you could remove it without impacting the system. The CP1434 H1 and the 343-1 IT modules can both speak ISO protocol. I will follow up with mor later billwest
	Bill West Principal Sales Application Engineer Siemens Industry, Inc. Digital Factory Division
Suggestion To thank Quote Answer

9/14/2013 10:27 AM	Rate (0)
Lex Advanced Member Joined: 12/12/2006 Last visit: 1/27/2020 Posts: 19 Rating: (0)	Dear billwest, The exiting system is used S7-317-2DP, and can't be to stop or shutdown for change anothers configuration, i must be to used IE/PB as Gateway mode for forwad data from CP1434H1 (TI505-1102CPU) i not be sure this solution is posibled or not? Please advice. Regards, Alex

Suggestion To thank Quote Answer

9/14/2013 10:59 AM	Rate (0)
Lex Advanced Member Joined: 12/12/2006 Last visit: 1/27/2020 Posts: 19 Rating: (0)	Addition Configuration of used . (Config V2.0) Please see attachement file and advice is correct or not? Regards, Alex. Attachment Config#02.gif (110 Downloads)

Suggestion To thank Quote Answer

9/16/2013 4:15 PM	Rate (0)
billwest Gold Expert Joined: 6/20/2007 Last visit: 8/4/2018 Posts: 510 Rating: (113)	I have attached the IE/PB manual. In reviewing the manual, it doesn't preclude connecting a 505 CPU with the ISO protthe CPU to stopocol. I just don't see a mechanism for getting or putting data from the 505 on the S7300 through Profibus without making changes to the S7-300 program. The S7-300 program can be modified without stopping the CPU. Hardware changes require. I don't know where to go from here. billwest Attachment IePbLink_e.pdf (100 Downloads)
	Bill West Principal Sales Application Engineer Siemens Industry, Inc. Digital Factory Division
Suggestion To thank Quote Answer

10/7/2013 6:17 PM	Rate (0)
SamTheEagle Bronze-Expert Joined: 2/10/2006 Last visit: 1/25/2021 Posts: 128 Rating: (12)	You can add a CTI 2577 Profibus DP slave adapter in the TI505 PLC. In the S7 PLC you will configure the TI505 as a Profibus slave. You can use up to 110 words Data in + 110 words data out for communication. No need for IEPN adapter. Regards, Carlo

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on