Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

UPLOAD from SIMOTION C using SIMOTION SCOUT

Created by: Jigs_C at: 3/15/2011 12:20 PM (8 Replies)

Rating (0)

Thanks 1

9 Entries

3/15/2011 12:20 PM	Rate (0)
Jigs_C Regular Member Joined: 6/1/2007 Last visit: 12/2/2019 Posts: 33 Rating: (1)	We have a system where in SIMOTION C (C230-2) is used for controlling four axes operation. However the system is running well. We have a project in SIMOTION Scout and we are also able to connect to the CPU but when online it shows that C230-2 and the axes and the programms are not there in the memory and we cannot monitor the parameters inside the CPU. In the project when online the C230-2, AXES and the program elements shows Red+Green Mark ahead of them.We tried uploading from the CPU using "Target System-->Download-->Configuration Data To PG" but it gives an error that there is no online consistency. We even created a new project and tried to upload to PG but still it gave the same error.Can anyone explain how to get the what is inside the CPU (memory) into our PG and save it as a project?Looking forward to possible solution.Thanks

Suggestion To thank Quote Answer

3/15/2011 12:57 PM	Rate (0)
ChristophD Diamond Expert Joined: 5/12/2006 Last visit: 12/7/2019 Posts: 16998 Rating: (2028)	Hello, which Version of Scout and SIMOTION C FW do you have? Regards Christoph

Suggestion To thank Quote Answer

3/16/2011 4:42 AM	Rate (0)
Jigs_C Regular Member Joined: 6/1/2007 Last visit: 12/2/2019 Posts: 33 Rating: (1)	Hi, Thanks for response We are using SIMOTION C, FW V 3.2. and SIMOTION SCOUT Version 3.2.0.2 Regards
	Last edited by: Jigs_C at: 3/16/2011 4:49 AM
Suggestion To thank Quote Answer

3/16/2011 10:10 AM	Rate (0)
ChristophD Diamond Expert Joined: 5/12/2006 Last visit: 12/7/2019 Posts: 16998 Rating: (2028)	Hello, with this Versions is no Upload avaiable. Upload is avaiable with version V4.1 of SIMOTION. Regards Christoph

Suggestion To thank Quote Answer

3/16/2011 10:52 AM	Rate (0)
Jigs_C Regular Member Joined: 6/1/2007 Last visit: 12/2/2019 Posts: 33 Rating: (1)	Hi I managed to find a project for the system in backup. I could go online and I think I could monitor the AXES configuration. But still there are messages that the Axes configuration in the control are not upto date. I am attaching the snaps here. I want to make sure that I am seeing the configuration parameter values in the controller and not the project. Can you please tell the meaning of the snaps? Thanks in advance. Attachment simotion_c (Using the backup project).JPG (271 Downloads)

Suggestion To thank Quote Answer

3/16/2011 10:53 AM	Rate (0)
Jigs_C Regular Member Joined: 6/1/2007 Last visit: 12/2/2019 Posts: 33 Rating: (1)	another snap where I had problem and it was saying that the axes does not exist in the controller. Attachment simotion_c_prblm.JPG (168 Downloads)

Suggestion To thank Quote Answer

2/21/2012 2:29 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 9/16/2019 Posts: 661 Rating: (5)	hy sir, did you solve this problem? thanks
	... thank you ...
Suggestion To thank Quote Answer

4/30/2012 1:51 PM	Rate (0)
Jigs_C Regular Member Joined: 6/1/2007 Last visit: 12/2/2019 Posts: 33 Rating: (1)	Yes, I could solve the problem with, exporting the axis config files and all other config files from the old backup and importing the same in the newproject and then downloading it to the controller. Though I did it almost a year back since then I am not working on siemens much. Hope this will help..Ziemens..

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users S_Moderator

1/16/2018 3:46 PM	Rate (0)
Jen_Moderator Moderator Joined: 6/19/2017 Last visit: 12/5/2019 Posts: 3672 Rating: (47)	New question published by german123 is split to a separate thread with the subject Can I upload the project using Simotion Scout v4.4 from Siemens C240 v4.1?. Best regards Jen_Moderator

Suggestion To thank Quote Answer

| |

Follow us on