Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

WINAC RTX 2010 Sp2 and VM

Created by: LBEBENEK at: 3/15/2013 5:18 PM (64 Replies)

Rating (28)

Thanks 21

Result pages:: |; 1 | 2 | 3 | 4; |

65 Entries

Entries per page: 10 | 20 | 50 | all

3/15/2013 5:18 PM	Rate (4)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Welcome. Today i install on Virtualized on Vmware Workstation 9 WIN7 32 bit WINAC RTX 2010 Sp2. I have I7 processor with VT support. Installation process passed 100% OK. But its strange. When i run the VM and guest system is loaded then processor is fully loaded. I change HAL timer period to 1000. Nothing better after this settings. Anybody have experiance of this issue ?? Please send me your configurations of RTX and VM( how many processors, setting etc.) . Best regards.
	Last edited by: O_Moderator at: 3/18/2013 9:56 AM new subject after splitting from /tf/WW/en/Posts/80706#top
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users Wicho rrussinov PChiocce80

3/25/2013 10:47 AM	Rate (7)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Welcome. I found solution for runFULLY virtual WINAC RT into VMWARE 9 for developing and testing enviroment. I have Vmware Workstation 9 and Win7 32 bit guest operating system. At Host WIN7 64 Bit. Let,s go: 1.Create VM at hardware compatibility 9 Version. (1 processor with 2 cores , 1 Ethernet Bridged Network Adapter) 2.In Vmware 9 VMX file You must add this lines (very important): ethernet0.virtualDev = "e1000e" bios440.filename="FUJITSU211_314.ROM" 3.Copy into VM folder file from attachment (ROM FILE). 4.Install WINAC RTX 2010 on OS 5.In station configuration Add in slot IF1 IE General card . If You prompted to install drivers from RTX then accept this. From Guest OS this card was removed. Its normal don,t panic . 6.Then From Step7 set IP addresfrom Menu --->PLC---->Edit Ethernet Node. 7. Load program and use Fully virtualized WINAC. If You Have some problems To set IP from Edit Ethernet Node from STEP7 then You can retrive config from WLD file added into attachment. IP addres is 172.16.1.80. If You have further questions don't hesitate to contact me. Best regards. Attachment WINACRTX_VM.zip (3288 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 13 thankful Users joakimsk Climacom Jason85 ketch Ahmad Magdy Q Project PChiocce80 MikeLin Eugen_ASU M Bunds sir_tyseven knezamo edek

4/25/2013 10:51 AM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Help not work.

Suggestion To thank Quote Answer

4/25/2013 1:43 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	What is your config. more details.

Suggestion To thank Quote Answer

4/25/2013 2:41 PM	Rate (1)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Windows 7 Ultimate 32Bit SIMATIC NET 2010 SIMATIC WINAC 2010 Update 2.CPU on virtual machine stay 100% i try to increase HAL but still the same.Suggestion? I follow your instruction and i think i do all correct. I write to you also private message. Attachment 2013-04-25_143843.jpg (1559 Downloads)

Suggestion To thank Quote Answer

4/26/2013 11:20 AM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Dr.Acrobat (no adobe) Windows 7 Ultimate 32Bit SIMATIC NET 2010 SIMATIC WINAC 2010 Update 2.CPU on virtual machine stay 100% i try to increase HAL but still the same.Suggestion? I follow your instruction and i think i do all correct. I write to you also private message. Welocme. Your config its ok. Enter the WINAC properties and uncheck SPEEDSTEP technology. Probbably SPEEDSTEP is active and preventing to idle state the CPU https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&objId=38616807&query=OBs+error&load=treecontent&lang=en&siteid=cseus&aktprim=0&objaction=csview&extranet=standard&viewreg=WW Best regards.

Suggestion To thank Quote Answer

4/26/2013 1:33 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	The problem and enter the WinAC because, unfortunately, the CPU is not connected and busy with task manager (see attached).Thanks.Regards Attachment Untitled.jpg (1173 Downloads)

Suggestion To thank Quote Answer

4/26/2013 2:09 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Welcome. I have this same issue. Its probblem to acces the vonfiguration because cpu 100%. I make some trick. I deinstall RTX and reinstall RTX. But when installation was finisched dont reboot PC. Enter RTX menu and disable SPEEDSTEP. After this reboot. Other solution is find in registry Speed step key and put 0 value.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users M Bunds

4/26/2013 2:38 PM	Rate (1)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	I try because on registry seems be OK (see attached) and other mistake i find is not possible insert CPU WinLC RTX from SIMATIC NCM Manager. Attachment Untitled.jpg (974 Downloads)

Suggestion To thank Quote Answer

4/26/2013 6:33 PM	Rate (1)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Removed all install just WinAC 4.6 not reboot but WinLC RTX CPU not possible open.Suggestion ?

Suggestion To thank Quote Answer

4/26/2013 10:50 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Welcome. 1. uninstal all 2 install and when pc want reboot not accept and open wianc and make settings. 3 After make neccesary setiing -reboot. If not ,possible set reg key value . All need info is in attachment. PS I hope do you not have HP hardware? Check your VMx file to exist rom file line. Sometimes if you make restore from snapschot vmx setting was change. Attachment rtx.jpg (1206 Downloads)

Suggestion To thank Quote Answer

4/26/2013 10:55 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Yes this config its OK. Finally check VMX file config. Because when i make restore points vmx config change in my solution. If You have HP hardware some people tell me to problems with them. Best regards. I hope to resolve Your problem.

Suggestion To thank Quote Answer

4/27/2013 11:21 AM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Could you check please if VMware file settings and if i put on correct mode (under virtual machine folder) file ROM.Thanks.Regards.is not HP but DELL. Attachment 2013-04-27_111822.zip (753 Downloads)

Suggestion To thank Quote Answer

4/29/2013 7:19 AM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 5/26/2020 Posts: 40 Rating: (21)	Dr.Acrobat (no adobe) Could you check please if VMware file settings and if i put on correct mode (under virtual machine folder) file ROM.Thanks.Regards.is not HP but DELL. Welcom I check Your config. Rom file its Ok but You have ethernet0.virtualDev = "e1000". You must change to ethernet0.virtualDev = "e1000e". Your ROM file its correct location. Evrything loks fine. I have too DELL Host maschine. Try to run your rtx into schared mode maybe You can enter the RTX config. If You want of course its possible I can make remote support to check Your config on Your PC ( ex. Teamviewier). Best regards.

Suggestion To thank Quote Answer

4/29/2013 9:09 AM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Don't worry be happy already installed on old laptop.Thanks.Regards.

Suggestion To thank Quote Answer

4/29/2013 2:24 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Just last question : 6.Then From Step7 set IP addres from Menu --->PLC----> Edit Ethernet Node.When i try automatically system remove SET PG/PC Interface ETH from Step 7 and is not possible communicate with WinLC RTX.WINACRTX CARD.wld is OK?Thanks.Regards.

Suggestion To thank Quote Answer

4/29/2013 3:30 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	??? Attachment Untitled.jpg (957 Downloads)

Suggestion To thank Quote Answer

4/29/2013 4:16 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 7/14/2020 Posts: 37 Rating: (3)	Solve PC internal Local.Thanks.Sorry for the apologyze.

Suggestion To thank Quote Answer

4/30/2013 7:36 PM	Rate (0)
FrankG Regular Member Joined: 5/30/2007 Last visit: 7/24/2020 Posts: 1 Rating: (0)	Hi, I have also set this up and would like to ask either one of you a question. Have you tried adding an OPC Server within your configuration? I have tried and can't get it to work. It allows, connections, OPC Server, etc. to be downloaded. But, you can't browse into the server either remote or local. It does not see the server with any client that I have tried while being on the local machine. Thanks in advance and have a great day. Frank

Suggestion To thank Quote Answer

6/11/2013 5:47 PM	Rate (0)
automatest Posts: 1 Rating: (0)	Per your instructions, the setup is done on VMware Workstation 9. I am using VMware Workstation 8. Is that going to work?
automatest Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

Result pages:: |; 1 | 2 | 3 | 4; |

65 Entries

Entries per page: 10 | 20 | 50 | all

|

Share this page:

Share this page on...

Follow us on