Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Op77 OS update failed

Created by: aliuta2000 at: 1/31/2012 7:36 PM (11 Replies)

Rating (0)

Thanks 2

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

1/31/2012 7:36 PM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 7/29/2025 Posts: 123 Rating: (4)	hello , i was doing an OS update to an op 77A using Cpu 315 2 Dp and mpi usb adapter (i do not have ppi cable ).Os update isneeded to be able to transfer new project on. he transfere all datas , 3 from 3 , and he erase flash memory data Prosave give me an error transfera data failed Now when i boot , is apear : fist time OP77A boot loader 2010 07.xx and after that goes to next screen to This device contains free software , see info/Setings for details . and remain here .. please help me to fix this to go to transfer area or to initial factory setings

Suggestion To thank Quote Answer

2/1/2012 5:43 AM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 12/6/2025 Posts: 1525 Rating: (231)	aliuta2000 hello , i was doing an OS update to an op 77A using Cpu 315 2 Dp and mpi usb adapter (i do not have ppi cable ).Os update isneeded to be able to transfer new project on. he transfere all datas , 3 from 3 , and he erase flash memory data Prosave give me an error transfera data failed Now when i boot , is apear : fist time OP77A boot loader 2010 07.xx and after that goes to next screen to This device contains free software , see info/Setings for details . and remain here .. please help me to fix this to go to transfer area or to initial factory setings Hello aliuta2000, Check this FAQ on How do you do an operating system update (OS update) on operator panels? In your case you may need either RS232/PPI Multi-master cable (6ES7 901-3CB30-0XA0) or USB/PPI Multi-master cable (6ES7 901-3DB30-0XA0) to
	Like it? Rate it!
Suggestion To thank Quote Answer

2/1/2012 8:10 AM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 7/29/2025 Posts: 123 Rating: (4)	I succed to have an USB-PPI Multi master cable . olso i have an CP 5711 Adapter also (is ok tu use CP 5711). i hope i will sove tonight should i mark there Booting ?? or just os update again
	Last edited by: aliuta2000 at: 2/1/2012 8:40 AM
Suggestion To thank Quote Answer

2/1/2012 9:33 AM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 12/6/2025 Posts: 1525 Rating: (231)	aliuta2000 I succed to have an USB-PPI Multi master cable . olso i have an CP 5711 Adapter also (is ok tu use CP 5711). i hope i will sove tonight Hello aliuta2000, You need either one of the above mentioned two cables only in case ofUpdate OS and Reset to Factory Settings. You will be able to Update OS with other supported cables but not perform a Reset to Factory Settings. since USB PC adapter (6ES7972-0CB20-0XA0) supports OP77A, CP5711 should not have any issues with downloading / Updating OS.
	Like it? Rate it!
Suggestion To thank Quote Answer

2/1/2012 9:38 AM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 12/6/2025 Posts: 1525 Rating: (231)	aliuta2000 should i mark there Booting ?? or just os update again You can check the option "Reset to factory settings" if the OS is not at all booting / only a blank screen is displayed. (this may happen if there's a power failure during updation of OS) If the above mentioned is not the case, you can uncheck the option and do OS update.
	Like it? Rate it!
Suggestion To thank Quote Answer

2/1/2012 7:43 PM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 7/29/2025 Posts: 123 Rating: (4)	Ihave got a meesage from Siemens support .They are telling me that is not supproted an Os update via Mpi / dp cable -CPU and OP , but in the OP manual is written that is working . i am toal agree with Siemens , now , but a need a procedure to get the panel from current state to normal running , and after taht to put my project on OP.
	Last edited by: aliuta2000 at: 2/6/2012 9:07 AM Last edited by: aliuta2000 at: 2/1/2012 7:44 PM
Suggestion To thank Quote Answer

2/1/2012 8:16 PM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 7/29/2025 Posts: 123 Rating: (4)	i succed to restore factory setings , but by pressing some key(s) . if i just let in "restore factory setings " nothing happend , but with some keys pressed (do not ask witch key cause i press them random arraows esc enter )OP start to do transfering restorey factory settings Also i have change on the back swich configure from all to line for DP/MPI/PPI to RS 422/485 . now i am doing an os update . and is in erasing flash -> copying to flash. I am using an USB-PPI multimaster cablle 6ES7 901-3DB30-0XA0 Thank you to all
	Last edited by: aliuta2000 at: 2/6/2012 9:05 AM
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users O_Moderator Ganes10

11/19/2015 2:34 PM	Rate (0)
Ziemens Gold Member Joined: 3/2/2007 Last visit: 11/19/2025 Posts: 999 Rating: (5)	it works. (no need for pressing keys on op77a) i did exactly as described in the below link. switch off the power supply for the operator panel. use usb to ppi cable, all op77a dip switch off. open prosave, select op77a and communication type. goto os update, select image file, and click reset to factory settings. click os update. power up the op77a. ... [ Resetting the Operating System to the Factory Settings (Booting) ] https://support.industry.siemens.com/cs/document/19701610/how-do-you-do-an-%22operating-system-update%22-(os-update)-or-%22reset-to-factory-settings%22-on-operator-panels?dti=0&lc=en-US
	... thank you ...
Suggestion To thank Quote Answer

11/19/2015 3:06 PM	Rate (0)
Ayman Elotaify Diamond Member Joined: 5/28/2008 Last visit: 12/28/2025 Posts: 4522 Rating: (843)	Hello, To solve your problem, you have to do the folowing steps: Reset the panel to factory setting using Prosave and using one of the following cables: RS232/PPI Multi-Master cable; 6ES7 901-3CB30-0XA0 OR USB/PPI Multi-Master cable; 6ES7 901-3DB30-0XA0 OR Right angle adapter (9-pin 1:1); 6AV6 671-8XD00-0AX0 Then download your project using WinCC flexible. For WinCC flexible 2008 SP3, it may ask you to update the OS. Accept and then start to download the project again. Please note that you cannot use MPI PC adapter for project download, OS update or reset to factory setting. You can use one of the three above cables or MPI (PG-S7) "6ES7 901-0BF00-0AA0" Hope this helps.
	Ayman Elotaify
Suggestion To thank Quote Answer

11/19/2015 3:55 PM	Rate (0)
Ziemens Gold Member Joined: 3/2/2007 Last visit: 11/19/2025 Posts: 999 Rating: (5)	thank you
	... thank you ...
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on