Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Problems with PLCsim V13 and TIA V13 SP1 for 1200

Created by: thanhph.tdm at: 4/27/2015 4:31 PM (21 Replies)

Rating (3)

Thanks 4

Result pages:: |; 1 | 2 | 3; |

22 Entries

Entries per page: 10 | 20 | all

4/27/2015 4:31 PM	Rate (0)
thanhph.tdm Posts: 2 Rating: (0)	Pls help me. I can not do the simulation s7 1200 with PLCsim V13 and TIA V13 SP1. Error: error downloading to module "PLC 1" Attachment Untitled.jpg (2495 Downloads)
thanhph.tdm Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

4/27/2015 5:16 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hello, 1.) you need PLCSIM V13.0 SP1 to simulate a S7-1200 2.) which PLC with which FW you have projected? 3.) in you screen the PLCSIM is not running/started Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Vivek Kansara

4/27/2015 8:29 PM	Rate (0)
James Cornett Posts: 1 Rating: (0)	The most likely cause of this error is an incorrect firmware version. PLCSIM supports simulation of the S7-1200 firmware version V4.0 and later. If the CPU in your project is an older firmware version, then attempting to download this to PLCSIM will result in the described error.
James Cornett Posts: 1 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Joshua H. AndriyDon

4/30/2015 9:14 AM	Rate (0)
wjmax Posts: 9 Rating: (0)	Hello, If you use 32bit version of windows it could cause problem too.
wjmax Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

5/1/2015 4:04 AM	Rate (0)
thanhph.tdm Posts: 2 Rating: (0)	Thanks for all support. Now, it can not connect to PLCSim 1200 although I do as the instruction. Pls tell me if this problem occurs because I use Win 8.1- 64 bit. Attachment Capture.JPG (1613 Downloads)
thanhph.tdm Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

5/1/2015 8:06 AM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	hi, no on my Win8.1 64bit system plcsim is working without problems. isd better you give detailed and better informations to analyze your problem. or you show in the other threads here in the forum for similar problems.

Suggestion To thank Quote Answer

5/21/2015 2:27 PM	Rate (0)
santhosh sundaram Posts: 171 Rating: (44)	pls tell whether the IP is assigning automatically in the plc sim v13 sp1... I think tats t problem
santhosh sundaram Posts: 171 Rating: (44)
Suggestion To thank Quote Answer

6/3/2015 11:45 AM	Rate (0)
CS Moderator Moderator Joined: 9/1/2005 Last visit: 10/31/2025 Posts: 4114 Rating: (195)	new question published by josep77 is split to a seperate thread with the subject Problem simulation S7-1214C V4.1 Best regards CS Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards CS Moderator
Suggestion To thank Quote Answer

6/3/2015 11:46 AM	Rate (0)
CS Moderator Moderator Joined: 9/1/2005 Last visit: 10/31/2025 Posts: 4114 Rating: (195)	new question published by Jav Pinz is split to a seperate thread with the subject Problems simulate a S7-1200 V3.0 or below Best regards CS Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards CS Moderator
Suggestion To thank Quote Answer

10/6/2015 10:18 AM	Rate (0)
Min_Moderator Posts: 4758 Rating: (122)	New question published by mariodiaooo is split to a separate thread with the subject Simulation s7 1200 with PLCsim V13 sp1, Error. Best regards Min_Moderator
Min_Moderator Posts: 4758 Rating: (122)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on