Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

WinCC V7.3 Trends Column width

Created by: Antri at: 12/1/2015 3:23 PM (7 Replies)

Rating (3)

Thanks 3

8 Entries

12/1/2015 3:23 PM	Rate (0)
Antri Posts: 45 Rating: (1)	Dear all, I have a project that the client wants to change the length of the column and also rotate the column name and move it at the centers of the screen. Please see attached screenshot for explanation. How can i proceed to these modifications? Attachment gas_trend.jpg (425 Downloads)
Antri Posts: 45 Rating: (1)
Suggestion To thank Quote Answer

12/2/2015 2:33 PM	Rate (0)
bg2492 Posts: 7298 Rating: (2188)	Hello Antri, the column are labels of the value-axes. It is not possible to rotate them or move them to the center of the control. If you would like to have something like a "legend", you can only use a Rulercontrol, below the Trendcontrol, where you can have a list of the curves. Regards Georg Berghof
bg2492 Posts: 7298 Rating: (2188)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Benoitasap

12/2/2015 3:22 PM	Rate (0)
Alex Mol Silver Member Joined: 9/2/2008 Last visit: 8/3/2025 Posts: 191 Rating: (43)	Hello Antri, I assume the only problem is that the trend labels are too long so you can not fully read them. At the bottom of your screenshot I see some free (grey) space. You can use this space to make your own legend. This is the way I always make my trend pages. I never use the "build-in" labels. See my screenshot Best regards, Alex Attachment Trend.png (346 Downloads)
	Problems don't exist, only challenges.
Suggestion To thank Quote Answer

12/4/2015 7:38 AM	Rate (0)
Antri Posts: 45 Rating: (1)	After explaining to the client that his demands are "not possible" he came up with a new one. He present me an older version of WinCC trend ( He doesn't know which) that when you click on a value a small table is popup with the values.Please see attached screenshot.. As far as i understand, and correct me if i am wrong, by reading the "Working with WinCC" manual you press the "Display value at this position" button and the table popup. I haven't find this button at V7.3 trends toolbar. I activate all the buttons but none of them is the right one. Can you please advice how to activate this button? Attachment Display value at this position value.jpg (361 Downloads)
Antri Posts: 45 Rating: (1)
Suggestion To thank Quote Answer

12/4/2015 7:55 AM	Rate (2)
bg2492 Posts: 7298 Rating: (2188)	Hello Antri, this is what I mentioned in my former post. "If you would like to have something like a "legend", you can only use a Rulercontrol, below the Trendcontrol, where you can have a list of the curves." With the "old" Trendcontrol, the Ruler-Table was a part of the Trendcontrol themself. With the "new" Trendcontrol (since V7.0), the Ruler-Table is a seperate control ("WinCC RulerControl"). you can place it below the Trendcontrol. To set it visible, you have to add the button "Ruler" to the Toolbar of the Trendcontrol. Regards Georg Berghof
bg2492 Posts: 7298 Rating: (2188)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Benoitasap

12/4/2015 8:28 AM	Rate (0)
Antri Posts: 45 Rating: (1)	I did the configurationof the RulerControl as in manual but when i press ruler button the table doesn't appear.
Antri Posts: 45 Rating: (1)
Suggestion To thank Quote Answer

12/4/2015 2:09 PM	Rate (1)
Alex Mol Silver Member Joined: 9/2/2008 Last visit: 8/3/2025 Posts: 191 Rating: (43)	Hello Antri, Did you select the right source (trend)? Check my settings. In this way the ruler control is always visible. Best regards, Alex Attachment RulerControl.png (459 Downloads)
	Problems don't exist, only challenges.
Suggestion To thank Quote Answer

12/7/2015 1:21 PM	Rate (0)
Antri Posts: 45 Rating: (1)	Dear Alex Mol Thanks for your answer. It really solved my problem.
Antri Posts: 45 Rating: (1)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Min_Moderator

|

Share this page:

Share this page on...

Related topics by keywords:

WinCC Picture Controls

Follow us on