Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

4 ANALOG INPUTS

Created by: Roose123 at: 12/21/2017 11:23 AM (6 Replies)

Rating (3)

Thanks 3

7 Entries

12/21/2017 11:23 AM	Rate (0)
Roose123 Posts: 3 Rating: (0)	Dear All, I have LOGO 8 24V, I need 4 analog inputs I have connected the inputs well, first time when the program is loaded it displays all the readings but if i switch off the logo and restart it does not recognize the 3rd and 4 analog out puts. Also when i save the program it says "AI position settings between circuit program and device are different Do you want to change the AI position setting of device" Thanking you in anticipation.
Roose123 Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

12/21/2017 11:34 AM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 12/25/2025 Posts: 36372 Rating: (4543)	By default, the LOGO! Base module 2 of the 4 AI enabled. Under the I / O settings you need to enable 4 AI. Then save the file and then to the LOGO! transfer. When the message"AI position settings between circuit program and device are different. Do you want to change the AI position setting of device?" appears, confirm with OK. Attachment LOGO! settings.PNG (340 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

12/21/2017 11:42 AM	Rate (0)
Roose123 Posts: 3 Rating: (0)	Thank you so much for your swift reply ! the IO setting was set to 4 as described and "AI position settings between circuit program and device are different. Do you want to change the AI position setting of device?" was confirmed as OK still the problem persists.
Roose123 Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

12/21/2017 11:45 AM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 12/25/2025 Posts: 36372 Rating: (4543)	How is the exact order number of your LOGO! ? How is the firmware version?

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

12/21/2017 11:56 AM	Rate (0)
Roose123 Posts: 3 Rating: (0)	I purchased from UAE distributor. software version is 8.1
Roose123 Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

12/21/2017 1:49 PM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 12/25/2025 Posts: 36372 Rating: (4543)	No matter who you bought from. I asked for the exact Siemens order number. She is at the LOGO! imprinted and starts with "6ED 1052-". Then comes a combination of 5 characters e.g. "1MD00". And ends with "-0BA8" if it's a LOGO! 0BA8 is I also asked for the firmware version and not the software version. The firmware version you can query with Software.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

4/3/2018 9:49 AM	Rate (0)
Jen_Moderator Posts: 8171 Rating: (174)	New question published by Stijn13h is split to a separate thread with the subject On the slave analog input AI1 & AI2. 3, 4 aren't working. Best regards Jen_Moderator
Jen_Moderator Posts: 8171 Rating: (174)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on