Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

CMR2020

Created by: Zazu at: 10/13/2015 10:40 AM (6 Replies)

Rating (1)

Thanks 9

7 Entries

10/13/2015 10:40 AM	Rate (1)
Zazu Bronze Member Joined: 3/4/2011 Last visit: 11/1/2022 Posts: 78 Rating: (4)	Has anyone got any knowledge of the CMR2020. I have one that seems to be stuck in configuration mode, after a power outage. (LED L is flashing). I can't access it via the web interface and even a factory reset doesn't seem to have any effect. Thanks in advance.

Suggestion To thank Quote Answer

10/13/2015 10:57 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/6/2025 Posts: 35929 Rating: (4498)	Power LED "L" flashes: Initialization or re-configuration is active. The SET button you pressed to the 10s longer to be reset to factory settings? If that did not help, I would start in your place a Support Request.

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Zazu RKBIS

10/13/2015 11:30 AM	Rate (0)
Zazu Bronze Member Joined: 3/4/2011 Last visit: 11/1/2022 Posts: 78 Rating: (4)	Thank you for the quick reply. I tried the 6 seconds and the 10 seconds. I think you are right in suggesting a support request.

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users ixo65 RKBIS

10/13/2015 5:40 PM	Rate (0)
Zazu Bronze Member Joined: 3/4/2011 Last visit: 11/1/2022 Posts: 78 Rating: (4)	Eventually got it to reset. The button was out of alignment and would only make contact in a certain position.

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users ixo65 RKBIS

10/13/2015 5:51 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/6/2025 Posts: 35929 Rating: (4498)	Hello Zazu, thanks for feedback.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

12/17/2015 11:58 AM	Rate (0)
pierrege Posts: 1 Rating: (0)	I have the same problem ... CMR2020 re-initialize continuously after power outage and it is unable to communicate with it. Is there any solution (new firmware or anything) or the only way is to use a UPS ?? --------------------------------------- PROBLEM SOLVED !! It seems that de initialization did not recognize the SIM card because there is NO PIN-CODE !! Since we have a new SIM card with PIN-CODE, there is no more problem to reboot after power outage.
pierrege Posts: 1 Rating: (0)	Last edited by: pierrege at: 1/5/2016 2:34:34 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

12/22/2015 9:58 AM	Rate (0)
Helmut_13 Posts: 2930 Rating: (432)	Hi, what Internet browser do you use? I had problems in the past with MS IE. Since this time I use Modzilla Firefox and it works. My effect: I cann't open the Web-page of the MCR any time, some times I could see the CMR's Web-page but I can't add information, some input field I can't see and so on. The manual then "told" me IE V11, Firefox V28.0 and Chrome V33.0 is supported. Hope this helps
Helmut_13 Posts: 2930 Rating: (432)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RKBIS

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on