Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Micromaster drives on profibus

Created by: practicalogical at: 3/22/2009 8:28 AM (6 Replies)

Rating (1)

Thanks 2

7 Entries

3/22/2009 8:28 AM	Rate (0)
practicalogical Posts: 3 Rating: (0)	Hi, I need to connect around 70 Micromaster/Sinamics G120 drves on profibus with a S7 300 PLC. Will CPU 315-2DP be sufficient for this?Or do i need to upgrade to 317-2DP Or to S7 400 seies? Do I need to consider repeaters? Pls advice. Practicalogical
practicalogical Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

3/22/2009 9:46 AM	Rate (0)
Darius Platinum Expert Joined: 9/28/2005 Last visit: 7/24/2025 Posts: 2957 Rating: (243)	Hi, Its 100% that you will need repeaters, but this is fullysuficient to use your CPU. If I'm not wrong you can address up to 127 DP slaves with this CPU and you can have 32 slaves per one network segment, so basically you'll need 3 repeaters (or more if you have long distances).
	Best regards, Darius
Suggestion To thank Quote Answer

3/22/2009 6:00 PM	Rate (0)
umencho Diamond Member Joined: 3/21/2006 Last visit: 3/30/2025 Posts: 10239 Rating: (1183)	Hello Just to mention. I don't think that 315-2DP will do the job - to be profibus master for too many slaves (drives). My suggestion is to upgrade to 317... or S7-400 SPU. I had the same story. One 315 CPU with 10 drives, connected like slaves. Even using 3 repeaters, decrease the baud rate, with around 50 m distance between master and slave - I can't to see all slaves. Just I changed this 315 to 416 CPU (unplug profibus connector from 315 and connect to 416, change in hardware configuration type of CPU, even inctrease the baud rate and download this configuration) after that everything was OK. Hope this will helps. regards

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Darius

3/22/2009 7:44 PM	Rate (0)
Darius Platinum Expert Joined: 9/28/2005 Last visit: 7/24/2025 Posts: 2957 Rating: (243)	Hi, I vannot agree with you UMENCHO . CPU 315 is fully capable of 124 slaves addressing and with repeaters it must be no problems. Believe me I had some plants in uzbekistan where 314 was holding >35 MicroMaster without any problems. Somewhere I had table where it was showing how much slaves I can connect on one repeater if I have some distance between slaves. I mean if my max distance between slaves is 15 meter than I can connect x slaves on one repearer and so on, but I lost this table somewhere. So if you use so much slaves you must pay attention at speeds, distances, repeaters and terminators. Offcourse 3 repeater may be not sufficent here, but still its very very possible to do on 315 CPU (its even too much CPU ).
	Best regards, Darius
Suggestion To thank Quote Answer

3/22/2009 7:55 PM	Rate (0)
umencho Diamond Member Joined: 3/21/2006 Last visit: 3/30/2025 Posts: 10239 Rating: (1183)	Hello Darius, For everything you are abselutely right. For possibilities of 315, speed, data distance... Of course, in each project, managers must make optimization and in this case 315 is first possible and "perfect" choice. . I just deceide to write here my bad expirience. regards

Suggestion To thank Quote Answer

3/22/2009 8:30 PM	Rate (0)
Darius Platinum Expert Joined: 9/28/2005 Last visit: 7/24/2025 Posts: 2957 Rating: (243)	I hope that everyone here (not only me) will value your experience and look at it again when making decision, because using so much drives will lead to the problems of calculation and design of system. Thanks for sharing your experience !
	Best regards, Darius
Suggestion To thank Quote Answer

3/22/2009 10:24 PM	Rate (1)
Darius Platinum Expert Joined: 9/28/2005 Last visit: 7/24/2025 Posts: 2957 Rating: (243)	I have found table I mentioned. Attached. Attachment profibus.jpg (316 Downloads)
	Best regards, Darius
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users umencho

|

Share this page:

Share this page on...

Follow us on