Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

About the Extend Telegram

Created by: Gaowei at: 9/20/2016 4:44 AM (14 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

15 Entries

Entries per page: 10 | all

9/20/2016 4:44 AM	Rate (0)
Gaowei Posts: 43 Rating: (0)	'cause i want to pass the servo actual torque value into the plc,so i operate some steps ,pls check up my attachment. but some error occurs. is it right ?thx. Attachment Error.doc (72 Downloads)
Gaowei Posts: 43 Rating: (0)	Last edited by: AutoGen_978828 at: 9/20/2016 4:45:35 AM
Suggestion To thank Quote Answer

9/20/2016 4:53 AM	Rate (0)
Gaowei Posts: 43 Rating: (0)	And the SINAMICS Intergrated Telegram setting interface ,there is no "set up adresses" button. i am very confused Attachment Sinamics Intergrated.PNG (115 Downloads)
Gaowei Posts: 43 Rating: (0)
Suggestion To thank Quote Answer

9/20/2016 7:49 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/30/2023 Posts: 21199 Rating: (2797)	Hello, error 1 : delete the telegrams in HWCOnfig and then set up adresses again error 2: the button only exist if you have created the SINAMICS in HWConfig If you create a Single Drive Unit in the project or transfer a Drive from lifelist to the project this button not exists. Regards Christoph

Suggestion To thank Quote Answer

9/20/2016 9:57 AM	Rate (0)
Gaowei Posts: 43 Rating: (0)	hello. can i make it visible? or how i know the adress of the each telegram ,cause i extend one word ,but i don't know the address? Attachment pic.PNG (74 Downloads)
Gaowei Posts: 43 Rating: (0)	Last edited by: AutoGen_978828 at: 9/20/2016 9:57:31 AM
Suggestion To thank Quote Answer

9/20/2016 10:12 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/30/2023 Posts: 21199 Rating: (2797)	Hello, no on this device you can't make it visible. Do you have the project from S7 with the device? Where you get the device in starter? Regards Christoph

Suggestion To thank Quote Answer

9/20/2016 11:00 AM	Rate (0)
Gaowei Posts: 43 Rating: (0)	ChristophD Hello, no on this device you can't make it visible. Do you have the project from S7 with the device? Where you get the device in starter? Regards Christoph hello sorry, i did not understand clearly , i used the TIA Portal ,and double click"Simotion configuration" and enter into to simotion . Attachment pic.PNG (72 Downloads)
Gaowei Posts: 43 Rating: (0)
Suggestion To thank Quote Answer

9/20/2016 11:18 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/30/2023 Posts: 21199 Rating: (2797)	Hi, please can you attach the project here? Which TIA Portal do you use? In simotion Scout TIA the button should always be visible! Regards Christoph
	Last edited by: ChristophD at: 9/20/2016 11:19:59 AM
Suggestion To thank Quote Answer

9/20/2016 1:45 PM	Rate (0)
Gaowei Posts: 43 Rating: (0)	ChristophD Hi, please can you attach the project here? Which TIA Portal do you use? In simotion Scout TIA the button should always be visible! Regards Christoph The project after being compressed is bigger than limit.i can't upload. I am using TIA V13 SP1.Update9. and Scout TIA V4.4.05. can i send the project in your email if allowed
Gaowei Posts: 43 Rating: (0)
Suggestion To thank Quote Answer

9/20/2016 1:52 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/30/2023 Posts: 21199 Rating: (2797)	Hello, load it oat dropboy or somthing an post the link. Regards Christoph

Suggestion To thank Quote Answer

9/20/2016 1:59 PM	Rate (0)
Gaowei Posts: 43 Rating: (0)	FYI . the link adress: http://pan.baidu.com/s/1slgr6SP
Gaowei Posts: 43 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on