Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Communicate ABB AC450 and s7 300 via dp / dp coupler

Created by: caupolican bravo at: 10/26/2012 9:44 PM (24 Replies)

Rating (1)

Thanks 1

Result pages:: |; 1 | 2 | 3; |

25 Entries

Entries per page: 10 | 20 | all

10/26/2012 9:44 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	Estimated I am with a similar problem I am trying to communicate with an ABB AC450 dp / dp coupler through a profibus trajeta ci451 a s7 300 and could not make communication and treaty if you have any examples of how to read the abb Siemens acopaldor investigated while best regards alexander from Chile
caupolican bravo Posts: 10 Rating: (0)	Last edited by: CS Moderator at: 11/6/2012 12:53 PM new subject after splitting from /tf/WW/en/Posts/66082#top
Suggestion To thank Quote Answer

10/27/2012 12:46 PM	Rate (0)
paul_wh Posts: 23 Rating: (0)	I have done a successful configuration for a DP/DP coupler (6ES7 158-0AD01-0XA0) to an AC450 using the same method. It will work as above. Can you confirm your hardware? Maybe post a picture of the hardware configuration you are attempting.
paul_wh Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

10/29/2012 10:13 AM	Rate (0)
paul_wh Posts: 23 Rating: (0)	Hi Alexander, See attached screenshots of my configuration of the DP coupler in online builder. This was based on a 500k Profibus network. Paul Attachment AC450 DP Coupler Configuration.zip (773 Downloads)
paul_wh Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

10/29/2012 8:35 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	thanks friend I'll try and tell you the settings as I was with the DP / DP a small query in s1 where you got the chain pin 10 S3 and I imagine are the settings hexa siemens I can esplicar this wuau que ayuda se pasaron saludos desde chile Attachment myconfig.JPG (604 Downloads)
caupolican bravo Posts: 10 Rating: (0)	Last edited by: caupolican bravo at: 10/29/2012 8:59 PM
Suggestion To thank Quote Answer

10/30/2012 10:41 AM	Rate (0)
paul_wh Posts: 23 Rating: (0)	Pin 10 is actually part of S2, it just looks like S1 from the snapshot. This is the hex settings from the Siemens hardware configuration. I have had to find the other settings from the GSD file, such as the general settings in S1 and configuration data in S4. I have assumed you are using online builder for configuration of the AC450. The best idea is to create a hardware configuration in Siemens as if it is the AC450 side. You can use a CPU315 for the master. Make sure you have the correct baud rate and address. You can post it or PM me and I can take a look if you like. Paul
paul_wh Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

10/31/2012 5:58 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	when I try to send data is going to stop both stations but when both are run unattended ok I'm testing with two s7 300
caupolican bravo Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

10/31/2012 8:45 PM	Rate (0)
paul_wh Posts: 23 Rating: (0)	On the second S7300 you have it set up for inputs right? (Got to be the opposite of the first side) You may need to check your error messages and follow that through.
paul_wh Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

11/5/2012 7:39 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	Here my configuration of 2 master s7 300 With the basic configuration go even stop 2 dp dp cpu although this ok attached my project saludos cbravo Attachment Master1.zip (462 Downloads)
caupolican bravo Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

11/5/2012 7:40 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	master2 Attachment Master2.zip (356 Downloads)
caupolican bravo Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

11/5/2012 7:41 PM	Rate (0)
caupolican bravo Posts: 10 Rating: (0)	fault Attachment fault.JPG (489 Downloads)
caupolican bravo Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on