Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Communication between TIA Portal and S7-300 via Rs232-MPI Adapter

Created by: miguel_lopez at: 4/12/2013 10:40 AM (14 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

15 Entries

Entries per page: 10 | all

4/12/2013 10:40 AM	Rate (0)
miguel_lopez Advanced Member Joined: 9/29/2011 Last visit: 2/10/2023 Posts: 23 Rating: (5)	Hi everybody, I want to communicate with TIA Portal Profesional V11 SP2 Update 5 with a S7-300 CPU, but I can't do it. I'm able to communicate with Step7 V5.3 with my cable. It's an RS232-MPI adapter. The problem is that I can't find the adapter in the online access of the TIA Portal. I attach a image capture of my online access. Thanks in advance. Attachment Imagen1.jpg (829 Downloads)
	Last edited by: miguel_lopez at: 4/12/2013 11:00 AM
Suggestion To thank Quote Answer

4/12/2013 12:38 PM	Rate (0)
Kampi Posts: 366 Rating: (30)	Hi please post here the exactly order number of the S7-300 CPU! maybe you should use some new interface (not RS232). regards
Kampi Posts: 366 Rating: (30)
Suggestion To thank Quote Answer

4/12/2013 6:08 PM	Rate (0)
miguel_lopez Advanced Member Joined: 9/29/2011 Last visit: 2/10/2023 Posts: 23 Rating: (5)	The S7-300 is a S7314C- 2DP. Reference: 314-6CF01-0AB0 The adapter is a MPI/DP RS-232 Adapter. Reference: 6ES7 972-0CA23-0XA0 As I said before, I'm able to communicate with the same hardware through Step7 V5.3. I'm trying with the TIA Portal V11 and I can't. I can communicate with S7-1200 through the ethernet adapter, but I don't know where to find the MPI adapter in the software. Maybe it's imposible and you need an USB adaptor. Thanks.

Suggestion To thank Quote Answer

4/17/2013 11:25 AM	Rate (0)
miguel_lopez Advanced Member Joined: 9/29/2011 Last visit: 2/10/2023 Posts: 23 Rating: (5)	Anyone know any solution?. Maybe I must try with TIA Portal V12?

Suggestion To thank Quote Answer

4/25/2013 1:48 PM	Rate (0)
miguel_lopez Advanced Member Joined: 9/29/2011 Last visit: 2/10/2023 Posts: 23 Rating: (5)	I still have the problem. Anyone can help me? Any Ideas?

Suggestion To thank Quote Answer

6/25/2013 10:35 PM	Rate (0)
iNEO-tech Posts: 2 Rating: (0)	Hello, I have the same problem. I'm able to communicate via MPI-USB adatper in Step 7 5.5, but not in TIA Step 7 Proffesional v12 even I selected the PC-Adapter (Auto) in Set PG/PC Interface. Does anybody know solution? regards Krzysztof
iNEO-tech Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

6/26/2013 6:20 AM	Rate (0)
DS SURESH KUMAR Bronze Member Joined: 4/17/2012 Last visit: 3/21/2023 Posts: 474 Rating: (10)	miguel_lopez Anyone know any solution?. Maybe I must try with TIA Portal V12? Hi , If you have PC adapter then you change the port configuration of PLC as profibus then start the accessible nodes on network definetly it will give you resut. here i attach some screenshot for your reference Attachment comm1.JPG (1040 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users S7 AUTOMAN

6/26/2013 11:17 PM	Rate (0)
iNEO-tech Posts: 2 Rating: (0)	Hi, the problem is that I have only TeleService and S7USB on the PG/PC list even I added and selected PC Adapter. Please find attached screens. regards, Krzysztof Attachment all.jpg (749 Downloads)
iNEO-tech Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

6/27/2013 6:24 AM	Rate (0)
DS SURESH KUMAR Bronze Member Joined: 4/17/2012 Last visit: 3/21/2023 Posts: 474 Rating: (10)	iNEO-tech Hi, the problem is that I have only TeleService and S7USB on the PG/PC list even I added and selected PC Adapter. Please find attached screens. regards, Krzysztof Hi , check the attachment you have to configure there and check it in Accessible nodes??? whether you are getting any device??? Attachment all.jpg (669 Downloads)

Suggestion To thank Quote Answer

10/17/2013 9:33 AM	Rate (0)
JanvS Posts: 3 Rating: (0)	I have the same problem. There is no way to enable the serial port PC adapter. I cannot produce the screen from picture COMM1.JPG. Can you please be a bit more specific in your explanation on how to configure this? I would be interested to see the settings under the tab 'Local Connection' on the picture 'ALL.JPG' but that one is not showing. In my case I have to set the 'Connection To': combo box option to COM1 to accommodate the MPI cable adapter. Thanks, Jan
JanvS Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on