Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

CPU313C Integrated IO problem

Created by: Kanag's at: 9/1/2008 4:53 AM (10 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

9/1/2008 4:53 AM	Rate (0)
Kanag's Posts: 54 Rating: (2)	Hi Iam using CPU313C model 313-5BF03-0AB0 firmware V2.6.6. I have downloaded the program. There are some digital inputs active in the integrated DI module. But the same is notappearing in the Step7. If I see in the VAT table it is showing as Inactive. Software couldnt able to read the integrated IO status. There are some additional IO cards available next to integrated IO cards. The IO status (DI) of additional cards are reflecting in Step7. I am using Step7 V5.4 + SP3 + HF1. Is there any problem in the HW connection? Can anybody guide me in this regard? -Kanag
Kanag's Posts: 54 Rating: (2)
Suggestion To thank Quote Answer

9/1/2008 6:23 AM	Rate (0)
Aret Posts: 2348 Rating: (264)	1. ChecklogicaladdressesinHWKonfig.My313CwasgixingdefaultintegratedinputsonI124... 2. Check voltage. If voltage of signal is lower, than 24Vitcanbe,thatLEDlits,butCPUdoesn'tseeit. 3. Export your HW config and put it here.
Aret Posts: 2348 Rating: (264)
Suggestion To thank Quote Answer

9/1/2008 6:44 AM	Rate (0)
Kanag's Posts: 54 Rating: (2)	Hi I have uploaded the HW configuration. The Digital IO is starting from I124.0 & Q124.0. Attachment simatic 300.zip (265 Downloads)
Kanag's Posts: 54 Rating: (2)
Suggestion To thank Quote Answer

9/1/2008 7:12 AM	Rate (0)
Aret Posts: 2348 Rating: (264)	After checking voltage (see rpevious post) try to do following: 1. Check frontconnector wiring. For I124.0 which pins do you connect? 2. Download HW 3. In HW config right click on module -> Monitor/Modify, then activate Monitor checkbox. 4. Alsocheckdiagnosticbuffer
Aret Posts: 2348 Rating: (264)
Suggestion To thank Quote Answer

9/1/2008 8:54 AM	Rate (0)
Darius Platinum Expert Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	Hello, Most likely it is voltage issue. Also I would suggest to set PLC into factory delivery state.
	Best regards, Darius
Suggestion To thank Quote Answer

9/1/2008 9:49 AM	Rate (0)
Khaled_Ezzat Silver Member Joined: 9/7/2007 Last visit: 10/9/2024 Posts: 550 Rating: (62)	Dear Darius, I think the problem is all about the Voltage that may cause this effect. That happened to me several times
	Best Regards
Suggestion To thank Quote Answer

9/1/2008 6:21 PM	Rate (0)
Kanag's Posts: 54 Rating: (2)	Hi Thanks for all your reply. It was the problem with supply voltage. It is solved now.
Kanag's Posts: 54 Rating: (2)
Suggestion To thank Quote Answer

9/29/2008 2:35 PM	Rate (0)
Felipe Schauenburg Posts: 2 Rating: (0)	I am having the same problem with the same CPU. Did the check list here. Checked the supply voltage and signal voltage and both are OK at 24V. The logical adresses are correct, and so is the other HW configuration. Could there be any other possible reason for that to happen? Best regards. Felipe
Felipe Schauenburg Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

9/30/2008 8:59 AM	Rate (0)
john Enthu Posts: 69 Rating: (0)	Dear Kanag, Please, descrbe your problem solution so that we can also have better knowledge in future for this kind of problems. is it more that 24 V Dc you have given to CPU? if else, please, describe in detail.ss regards............
john Enthu Posts: 69 Rating: (0)
Suggestion To thank Quote Answer

9/30/2008 11:18 AM	Rate (0)
Kanag's Posts: 54 Rating: (2)	Hi We have to give supply voltage to the CPU and also to all Integrated IO cards.If the supply voltage to IO cards is not there the input signal (DI) will indicate only in the card level i.e. only LED glows but the CPU cannot read the input. After giving the supply voltage to the CPU & IO cards the problem was solved. -Kanag
Kanag's Posts: 54 Rating: (2)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users OMKRIS2017

|

Share this page:

Share this page on...

Follow us on