Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Disconnect CM1241 while S7-1200 is running

Created by: Tresancos at: 2/23/2012 3:48 PM (9 Replies)

Rating (0)

Thanks 0

10 Entries

2/23/2012 3:48 PM	Rate (0)
Tresancos Posts: 12 Rating: (0)	I worked with S7-1214 and a commnunications module. I don't know why but sometimes the PLC changes its state since RUN -> STOP and the ERROR led start to blink. The diagnostic buffer shows three events: First: HW configuration error. Extraction of the HW component (ID 02.4042) Second: New information of Start Blocked: CPU is operating now as STOP(ID 02.4000) Thrid:HW configuration error. Insemption of the HW component (ID 02.4042) This happen suddenly and without sense. Could I use some block on the PLC, that if this happen the PLC continuous working on: RUN??? Thanks!!!!!
Tresancos Posts: 12 Rating: (0)
Suggestion To thank Quote Answer

2/23/2012 4:02 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 3/21/2023 Posts: 13199 Rating: (2146)	Tresancos I worked with S7-1214 and a commnunications module. I don't know why but sometimes the PLC changes its state since RUN -> STOP and the ERROR led start to blink. The diagnostic buffer shows three events: First: HW configuration error. Extraction of the HW component (ID 02.4042) Second: New information of Start Blocked: CPU is operating now as STOP(ID 02.4000) Thrid:HW configuration error. Insemption of the HW component (ID 02.4042) This happen suddenly and without sense. Could I use some block on the PLC, that if this happen the PLC continuous working on: RUN??? Thanks!!!!! What firmware and what version of portal are you using? FW 2.2 for the S7-1214C seems to help avoid many crashes with TIA Portal V11 SP2 If you use your own error handling by creating a diagnostic error routine OB, the PLC will usually try to run that OB instead of crashing. Create one diag OB, compile, and download. See if that helps. You might want to check your connection with the hardware between the comm unit and the PLC. It might be loose. If it is snug, you may have a ground loop or some high EMF signal nearby.
	science guy
Suggestion To thank Quote Answer

2/23/2012 5:14 PM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 3/16/2023 Posts: 1498 Rating: (217)	Tresancos I worked with S7-1214 and a commnunications module. I don't know why but sometimes the PLC changes its state since RUN -> STOP and the ERROR led start to blink. The diagnostic buffer shows three events: First: HW configuration error. Extraction of the HW component (ID 02.4042) Second: New information of Start Blocked: CPU is operating now as STOP(ID 02.4000) Thrid:HW configuration error. Insemption of the HW component (ID 02.4042) This happen suddenly and without sense. Could I use some block on the PLC, that if this happen the PLC continuous working on: RUN??? Thanks!!!!! Hello Tresancos, Can you post the diagnostic buffer text file here? Are you using any Digital Output of relay type? Let know the complete configuration of your S7-1200 sytem (IO modules, Communication modules used while the error occured)
	Like it? Rate it!
Suggestion To thank Quote Answer

2/24/2012 9:09 AM	Rate (0)
Tresancos Posts: 12 Rating: (0)	The diagnose buffer file that appears to me is: Diagnostics buffer of the module S71200\CPU\CPU_1214C\MDD_6ES7214-1HE30-0XB0_1.0 Order no. / description. Component Version 6ES7 214-1HE30-0XB0 Hardware 1 - - - Firmware V 1.0.2 Boot loader Firmware expansion --- Rack: 0 Slot: 1 Details on event: 1 of 9; Event ID:16#02:400C CPU info: Follow-up operating state transition Power-on mode set: WARM RESTART --> RUN Pending startup inhibit(s): - No startup inhibit set CPU switches from STARTUP to RUN state Incoming event 2/24/2012 8:56:17.539 AM Details on event: 2 of 9; Event ID:16#02:400C CPU info: Follow-up operating state transition Power-on mode set: WARM RESTART --> RUN Pending startup inhibit(s): - No startup inhibit set CPU switches from STOP to STARTUP state Incoming event 2/24/2012 8:56:17.532 AM Details on event: 3 of 9; Event ID:16#02:400C CPU info: Follow-up operating state transition Power-on mode set: WARM RESTART --> RUN Pending startup inhibit(s): - No startup inhibit set CPU switches from STOP (initialization) to STOP state Incoming event 2/24/2012 8:56:17.525 AM Details on event: 4 of 9; Event ID:16#02:3951 Module message: Hardware component removed or missing. Function continued (system reaction) HW ID= 13 Incoming event 2/24/2012 8:56:17.523 AM Details on event: 5 of 9; Event ID:16#02:4001 CPU info: Power on - Memory card type: No memory card CPU switches from NO POWER to STOP (initialization) state Incoming event 2/24/2012 8:56:11.186 AM Details on event: 6 of 9; Event ID:16#02:4002 CPU info: Power off CPU switches from STOP to NO POWER state Incoming event 2/24/2012 8:56:05.818 AM Details on event: 7 of 9; Event ID:16#02:4042 CPU error: Hardware configuration error - Plugging of hardware component restricted CPU switches to STOP state, new startup inhibit set: .. - System request for power cycle Incoming event 2/24/2012 8:55:58.846 AM Details on event: 8 of 9; Event ID:16#02:4000 CPU info: New startup inhibit information Pending startup inhibit(s): - System request for power cycle Current CPU operating state: STOP Incoming event 2/24/2012 8:55:37.942 AM Details on event: 9 of 9; Event ID:16#02:4042 CPU error: Hardware configuration error - Removal of hardware component restricted CPU switches to STOP state, new startup inhibit set: .. - System request for power cycle
Tresancos Posts: 12 Rating: (0)
Suggestion To thank Quote Answer

2/24/2012 9:14 AM	Rate (0)
Tresancos Posts: 12 Rating: (0)	The 7, 8 and 9 happens without do anything and the other six when i conmute the plc between power off /on Ganes10: My system consists in CPU1214C DC/DC/RLY with a CM1241 and a SM1231. huggy_d1:The firmware of my PLC isV 1.0.2for the S7-1214C and i am working with TIA Portal V10.5 SP2 I like that if this error happens my PLC continue RUNNING. Is it possible? Thanks!!!
Tresancos Posts: 12 Rating: (0)
Suggestion To thank Quote Answer

2/24/2012 1:49 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 3/21/2023 Posts: 13199 Rating: (2146)	Tresancos The 7, 8 and 9 happens without do anything and the other six when i conmute the plc between power off /on Ganes10: My system consists in CPU1214C DC/DC/RLY with a CM1241 and a SM1231. huggy_d1:The firmware of my PLC isV 1.0.2for the S7-1214C and i am working with TIA Portal V10.5 SP2 I like that if this error happens my PLC continue RUNNING. Is it possible? Thanks!!! I urge you to upgrade the firmware and your tia portal software to V11 SP2. The firmware in your project needs to also match. That said, it is possible by adding the hardware diag ob your plc may not halt on this type of error, but with V10.5 SP2 and FW 1.0.2, I am not sure. FW 2.x seems to have greatly improved on random cpu halts!
	science guy
Suggestion To thank Quote Answer

2/25/2012 1:50 PM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 3/16/2023 Posts: 1498 Rating: (217)	Tresancos The 7, 8 and 9 happens without do anything and the other six when i conmute the plc between power off /on Hello Tresancos, you are saying error 7, 8 and 9 happens without doing anything, but what does your subject means then ?
	Like it? Rate it!
Suggestion To thank Quote Answer

2/27/2012 10:51 AM	Rate (0)
Tresancos Posts: 12 Rating: (0)	Ganes10: This is the error that appears if the module CM1241 is disconnected when the PLC is running. In my case the error happened with all the modules connected. Maybe is a problem of the modbus between the PLC and the CM1241, because nobody had disconnected the CM. I wish if this happen to me again, the PLC continuous in RUNNING mode, not like now that change to STOP. Is this possible?
Tresancos Posts: 12 Rating: (0)
Suggestion To thank Quote Answer

2/27/2012 11:22 AM	Rate (0)
Ganes10 Platinum Member Joined: 8/31/2010 Last visit: 3/16/2023 Posts: 1498 Rating: (217)	Tresancos Ganes10: This is the error that appears if the module CM1241 is disconnected when the PLC is running. In my case the error happened with all the modules connected. Maybe is a problem of the modbus between the PLC and the CM1241, because nobody had disconnected the CM. I wish if this happen to me again, the PLC continuous in RUNNING mode, not like now that change to STOP. Is this possible? Hello Tresancos, Then as huggy said do upgrade the Operating System of the CPU to v2.2 and use the Diagnostics OB to prevent the CPU entering into STOP mode.
	Like it? Rate it!
Suggestion To thank Quote Answer

4/18/2015 4:54 PM	Rate (0)
CS Moderator Moderator Joined: 9/1/2005 Last visit: 2/27/2023 Posts: 4097 Rating: (192)	new question published by samvaz is split to a seperate thread with the subject CPU 1214 DC/DC/DC v4.0 (214-1AG40-0XB0) Errormessage . Best regards CS Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards CS Moderator
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on