Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Error Alarm 380500

Created by: Sam Jang at: 10/14/2011 7:11 AM (6 Replies)

Rating (1)

Thanks 1

7 Entries

10/14/2011 7:11 AM	Rate (0)
Sam Jang Posts: 4 Rating: (0)	Hello Experts, We have equipped with 6 axes+ spindlelaser cutting machinewith 840Di controller. Recently controller displays error as NC not ready. Checked in alarm msgs & following alarms/msgs found displayed. 25201 ... Axis X(all axis)drive fault; 25202 ... Axis X(all axis) waiting for drive. 380500 Profibus DP: fault of drive X(all axis) code 129 value 128 time 4 What means of code 129? See the attachment. DP address 11 is ET200s. What means of read color (Sync. with NC) lamp? Can any one help me as what could be the problem & best possible remedy? Thanks in the advance. Attachment P111012002.jpg (884 Downloads)
Sam Jang Posts: 4 Rating: (0)	Last edited by: Sam Jang at: 10/14/2011 7:32 AM
Suggestion To thank Quote Answer

10/14/2011 9:17 AM	Rate (1)
320 Advanced Member Joined: 5/31/2011 Last visit: 10/3/2024 Posts: 5 Rating: (1)	Hi What kind of Drive system do you use ? If you use YASKAWA Drive. Alarm 380500 code129 means "encoder data is lost" . Remedy: machine data 2798(Drive function) set 2 and update. Then alarm disappear after NCK reset or machin power OFF/ON. After this procedure. you must set Reference position. Best regards 320
	Last edited by: 320 at: 10/14/2011 9:27 AM Last edited by: 320 at: 10/14/2011 9:20 AM
Suggestion To thank Quote Answer

10/14/2011 12:48 PM	Rate (0)
Sam Jang Posts: 4 Rating: (0)	Thank you so much, 320. We use YASKAWA Drive. We cleared Alarm 380500 code 129 with your solution. After that,we set Reference position. But, we got other Alarm, 380500 code 147 value 144, after updating. Please, give me remedy again. And give me YASKAWA Drive fault code list & remedy, If possbile. Thank you very much.
Sam Jang Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

10/26/2011 7:32 AM	Rate (0)
320 Advanced Member Joined: 5/31/2011 Last visit: 10/3/2024 Posts: 5 Rating: (1)	Hi Alarm 380500 code 147 means "encoder battery worning" This alarm occured when battery voltage is lower than 21.3V. Remedy: repalace battery(ER6VC3N) procedure is see attatched. If alarm is not dissapear after battery replaced.further problem is possible. 1,Battery connecter joints incorrect. check joint. 2,Encoder cable is breaking.check encoder cable 3,Servopack is hardwear fault.Replace servopack. best regards 320 Attachment ER6VC3N Replacement Procedure2008_1_18.pdf (1092 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users tomas94

10/26/2011 7:34 AM	Rate (0)
320 Advanced Member Joined: 5/31/2011 Last visit: 10/3/2024 Posts: 5 Rating: (1)	and Alarm code list for you. Attachment alarm_UK.pdf (1289 Downloads)

Suggestion To thank Quote Answer

12/14/2017 6:47 AM	Rate (0)
aavaa Posts: 1 Rating: (0)	hi dear i have this error 380500 code 39 value 2097152 time 1 please help me Attachment photo_2017-12-14_09-14-26.jpg (605 Downloads)
aavaa Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

8/14/2024 11:35 AM	Rate (0)
U_2a5d843f-9643-4... Joined: 4/24/2024 Last visit: 8/14/2024 Posts: 1 Rating: (0)	Hello, please, did you solve this fault, i have a same problem. Thanks for any usefull answer for solution. Regards David

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on