Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Fault Codes in Simotion D435

Created by: Parthiban.R at: 12/31/2016 8:51 AM (10 Replies)

Rating (2)

Thanks 2

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

12/31/2016 8:51 AM	Rate (0)
Parthiban.R Advanced Member Joined: 3/13/2010 Last visit: 2/8/2024 Posts: 40 Rating: (0)	Hi Guys, Good Afternoon. I am facing some faults code in Simotion System. The following faults are presents in my system. D435 -- OK Fault: SINAMICS_Integrated : B_INF_02 -- 1910 : Fieldbus: setpoint timeout Fault: SINAMICS_Integrated : Control_Unit -- 1915 : PB/PN clock cycle synchronous operation sign-of-life failure drive object 1 Fault: SINAMICS_Integrated : SERVO_04 -- 1915 : PB/PN clock cycle synchronous operation sign-of-life failure drive object 1 Please advise me to solve clear the faults. Regards, RP Attachment Simotion_Error Msg.png (1108 Downloads)

Suggestion To thank Quote Answer

12/31/2016 9:03 AM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Helo, is the Simotion in STOP? -> set it to RUN Do you have the complete diagnostic buffer ? (Save it as txt and attach it here) What do you do to get this faults? The faults all from the SINAMCIS_Integrated . The F1910 often happens if PLC go to stop and cyclic Dataexchange stoped. The F1915 normaly comes up if the Simotion is Sync to external clock Source (I-Slave or I-Device mode) Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Parthiban.R

1/1/2017 4:11 PM	Rate (0)
Parthiban.R Advanced Member Joined: 3/13/2010 Last visit: 2/8/2024 Posts: 40 Rating: (0)	Hi Friends, I am currently facing a problem in Simotion D System. I am trying to ON the servo motor using Control Panel. When i am trying to switch on motor the error will come. 7900: Drive motor blocked/speed controller at its limit. Please advice me to solve this issues. BR, RP Attachment Motor Blocked.png (922 Downloads)

Suggestion To thank Quote Answer

1/2/2017 12:03 AM	Rate (1)
Jeff Casagrande Posts: 1529 Rating: (203)	1. Your brake is not releasing 2. Your motor leads are reversed (must be U-U, V-V, W-W) 3. Your feedback leads are reversed.
Jeff Casagrande Posts: 1529 Rating: (203)
Suggestion To thank Quote Answer

1/2/2017 7:35 AM	Rate (0)
Parthiban.R Advanced Member Joined: 3/13/2010 Last visit: 2/8/2024 Posts: 40 Rating: (0)	Hi Jeff, Thank You. Problem Solved

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users CS Moderator

1/4/2017 7:33 PM	Rate (0)
Parthiban.R Advanced Member Joined: 3/13/2010 Last visit: 2/8/2024 Posts: 40 Rating: (0)	Hi Friends, I am currently facing some faults in Simotion D435-2. When i am trying to activate the position using MCC chart the following error will comes. 40005 Missing Enables. 30002 Commend Aborted Also please confirm KTP1200 Basic 2nd Generation HMI will support Simotion D435-2 PN/DP. I am trying to connect the HMI with Profinet interface.But connection was not established. Kindly suggest me to sort out the issues. BR, RP Attachment Error1.png (883 Downloads)
	Last edited by: Parthiban.R at: 1/4/2017 7:34:36 PM
Suggestion To thank Quote Answer

1/5/2017 6:29 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Hello, looks that the _enableAxis command is not executed correctly. Which status have the connected drive in "diagnostic Overview"? Which option you have set in the _EnableAxis command for the next command? What is the Signal "Head_enable" which you use? The BasicPanles are compatible, but with some Restrictions (No Alarm/Alarm_s, if i remember correctly). For a further analyze you must give more Informations! Regards Christoph
	Last edited by: ChristophD at: 1/5/2017 6:30:43 AM
Suggestion To thank Quote Answer

1/9/2017 10:31 PM	Rate (0)
Parthiban.R Advanced Member Joined: 3/13/2010 Last visit: 2/8/2024 Posts: 40 Rating: (0)	Hi Friends, Currently i am working one Hose Wrapping Machine Application. In that machine totally three axes we are using with Simotion D 435-2 PN/DP controller. The following are the axes mechanics details. Head_Rotary Axes (Master) Motor Revolution - 106 & Load Revolution - 56 CAT_Linear Axes (Slave) Motor Revolution 1 & Load Movement 24.17mm Spool_Rotary Axes Motor Revolution 1 & Load Revolution 1 I want to maintain the tape pitch. How to maintain the tape pitch? 2. In the same same projects I want to control the Winder & Unwinder section in my simotion system. For winder and unwinder we are using G120 drive & CU250S with encoder feedback using Dancer Position Sensor FB. How to control winder & unwinder? 3. I want to use analog scaling and unscaling block in Simotion D system. In command library this instructions are not available. How to call this fucntions in my simotions program? Kindly suggest me. BR, RP

Suggestion To thank Quote Answer

10/25/2017 11:33 AM	Rate (0)
Amit Kumar @ Auto... Posts: 3 Rating: (0)	Parthiban.R Hi Friends, Currently i am working one Hose Wrapping Machine Application. In that machine totally three axes we are using with Simotion D 435-2 PN/DP controller. The following are the axes mechanics details. Head_Rotary Axes (Master) Motor Revolution - 106 & Load Revolution - 56 CAT_Linear Axes (Slave) Motor Revolution 1 & Load Movement 24.17mm Spool_Rotary Axes Motor Revolution 1 & Load Revolution 1 I want to maintain the tape pitch. How to maintain the tape pitch? 2. In the same same projects I want to control the Winder & Unwinder section in my simotion system. For winder and unwinder we are using G120 drive & CU250S with encoder feedback using Dancer Position Sensor FB. How to control winder & unwinder? 3. I want to use analog scaling and unscaling block in Simotion D system. In command library this instructions are not available. How to call this fucntions in my simotions program? Kindly suggest me. BR, RP Attachment Untitled picture.png (666 Downloads)
Amit Kumar @ Auto... Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

10/25/2017 11:52 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Pagall Parthiban.R Hi Friends, Currently i am working one Hose Wrapping Machine Application. In that machine totally three axes we are using with Simotion D 435-2 PN/DP controller. The following are the axes mechanics details. Head_Rotary Axes (Master) Motor Revolution - 106 & Load Revolution - 56 CAT_Linear Axes (Slave) Motor Revolution 1 & Load Movement 24.17mm Spool_Rotary Axes Motor Revolution 1 & Load Revolution 1 I want to maintain the tape pitch. How to maintain the tape pitch? 2. In the same same projects I want to control the Winder & Unwinder section in my simotion system. For winder and unwinder we are using G120 drive & CU250S with encoder feedback using Dancer Position Sensor FB. How to control winder & unwinder? 3. I want to use analog scaling and unscaling block in Simotion D system. In command library this instructions are not available. How to call this fucntions in my simotions program? Kindly suggest me. BR, RP do you have a question or problem?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on