Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

P0010 value cannot be changed

Created by: mayank_254 at: 10/5/2011 8:47 AM (14 Replies)

Rating (3)

Thanks 16

Result pages:: |; 1 | 2; |

15 Entries

Entries per page: 10 | all

10/5/2011 8:47 AM	Rate (0)
mayank_254 Posts: 20 Rating: (0)	Hi all, I am facing one problem with MM440, i cannot change the value of P0010 in the drive. it is consistently showing value 2 (For service purpose only). i have even tried to factory reset the drive but it is also not possible. What can be the reason as i am new to this drive i cannot figure what could be the reason behind this. Please help, its a bit urgent.
mayank_254 Posts: 20 Rating: (0)
Suggestion To thank Quote Answer

10/5/2011 12:53 PM	Rate (3)
Barlera Experienced Member Joined: 2/21/2011 Last visit: 4/18/2024 Posts: 52 Rating: (12)	Hi mayank_254. Do this steps: P0003 = 3 P0004 = 0 r0200 = only see this value P0201 = r0200 This parametrization will resolve your problem. Best Regards, Henrique Barlera

Suggestion To thank Quote Answer
This contribution was helpful to 6 thankful Users NAFNAF habraham ankolekar krsv80 Martin472 Maurobaumgarten

10/21/2011 2:12 PM	Rate (0)
mayank_254 Posts: 20 Rating: (0)	heyy, thanks for your reply, i tried with your mentioned parameters but nothing happened with that too. i am still not being able to change the value in the parameter P0010. If there is any other way or some other parameters that needs to be changed, please suggest me for that. I have tried other things as well but all in vain. Also the factory reset cannot be done as P0010 cannot be changed to its value for factory reset.
mayank_254 Posts: 20 Rating: (0)
Suggestion To thank Quote Answer

11/10/2011 1:54 PM	Rate (0)
Sarrito Posts: 1 Rating: (0)	mayank_254 heyy, thanks for your reply, i tried with your mentioned parameters but nothing happened with that too. i am still not being able to change the value in the parameter P0010. If there is any other way or some other parameters that needs to be changed, please suggest me for that. I have tried other things as well but all in vain. Also the factory reset cannot be done as P0010 cannot be changed to its value for factory reset.
Sarrito Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

11/11/2011 6:05 PM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 11/12/2024 Posts: 1505 Rating: (325)	Hi, We have had a similar experience when a customer (who "Could not remember what he had done") returned a drive to Siemens that was stuck in P10=1 (Quick Commissioning) We had tried everything, P3=3, P4=0, P3900=0. We tried service level 4, but it would not allow us access due to the state of P10. We also attempted to download the Power Stack data again, but this failed. After informing the German helpdesk, and as this was only a Frame Size A drive, they suggested recycling My question to you is . . . When did this happen, were you changing Inverter (P10=2) values at the time? If we can try and identify when this happens, maybe we could work out why. Regards, Graeme

Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users Ayman Elotaify Vithani mayank_254

11/12/2011 8:08 AM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	Hello, Recently, more than three users on the forum asked about the same problem. And tell now we still searching for a solution. And also I should thank "Mr. Expert Graeme" who shared info from German help desk.thank you Graeme. Graeme ................. After informing the German helpdesk, and as this was only a Frame Size A drive, they suggested recycling ......... I am fully agree with German help desk sugesstion to recycle the drive. As its size is FSA and it may consume a long time to solve the problem. Prices of FSA inverters are normally cheap. But what if the drive is a large scale one and faced the same problem. For this sake I do recommend to keep this thread open till found a solution for this problem. With best regards.
	Ayman Elotaify
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Vithani mayank_254

10/26/2014 4:41 AM	Rate (0)
NAFNAF Posts: 4 Rating: (0)	Barlera Hi mayank_254. Do this steps: P0003 = 3 P0004 = 0 r0200 = only see this value P0201 = r0200 This parametrization will resolve your problem. Best Regards, Henrique Barlera It is sunday, i am actualy in China and you made my day. thanks so much.
NAFNAF Posts: 4 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users habraham

8/12/2016 7:04 PM	Rate (0)
whyisthisso Posts: 2 Rating: (0)	I am having a similar problem with P0010 parameter on a micromaster 440, was any solution found?
whyisthisso Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

8/12/2016 10:33 PM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 11/12/2024 Posts: 1505 Rating: (325)	Hi, if you search similar threads, we found a "possible" solution: Set P927 = 0xF or so that it displays b - - n n regards, Graeme

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users PAKITO_PTS AutoGen_4635865

8/13/2016 1:07 PM	Rate (0)
whyisthisso Posts: 2 Rating: (0)	I already check this parameter and it is b--nn, any other suggestions?
whyisthisso Posts: 2 Rating: (0)	Last edited by: whyisthisso at: 8/13/2016 1:07:49 PM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on