Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

problem with 2nd generation panels in tia v13

Created by: AutoGen_1024398 at: 3/3/2015 10:47 AM (7 Replies)

Rating (3)

Thanks 11

8 Entries

3/3/2015 10:47 AM	Rate (0)
AutoGen_1024398 Regular Member Joined: 2/6/2015 Last visit: 10/15/2021 Posts: 14 Rating: (1)	Hello, If I want to run a simulation with the 2nd generation panel, do not display the screen.(see image below) If I replace the panel to 1nd generation, simulation works. The problem is with all the 2nd generation panels. Matej Copik Attachment panel 2nd gen.jpg (532 Downloads)

Suggestion To thank Quote Answer

3/3/2015 11:18 AM	Rate (0)
enof Silver Member Joined: 2/10/2012 Last visit: 12/6/2024 Posts: 314 Rating: (59)	me too. 1 generation (what a name) works.

Suggestion To thank Quote Answer

3/4/2015 11:06 AM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 12/9/2024 Posts: 4358 Rating: (1454)	Hi, I hadn't problems to simulate my HMI 2nd generation (just as reference). The print screen that you post looks like as low PC in low memory state... I suggest you to take a look in windows task manager how works the PC at the simulation moment... Else open a Support Request and tell us what they answers to you.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

3/5/2015 7:35 AM	Rate (0)
AutoGen_1024398 Regular Member Joined: 2/6/2015 Last visit: 10/15/2021 Posts: 14 Rating: (1)	My computer: CPU: i5-3337, 2x1.8GHz RAM: 6GB below is picture from Task manager. I try write to support. Matej Attachment CPU+memory.png (445 Downloads)

Suggestion To thank Quote Answer

3/6/2015 8:27 AM	Rate (1)
AutoGen_1024398 Regular Member Joined: 2/6/2015 Last visit: 10/15/2021 Posts: 14 Rating: (1)	Hi, a send request to support, and problem was in graphics card. Driver on graphic card was correct installed, but I try reinstall newer driver on graphic card, and the simulation work correctly. Matej

Suggestion To thank Quote Answer
This contribution was helpful to 6 thankful Users Min_Moderator Denilson Pegaia enof Rana Ali crazyCow caki3000

1/26/2017 1:28 PM	Rate (2)
Jorsal2 Advanced Member Joined: 12/1/2016 Last visit: 9/26/2024 Posts: 12 Rating: (14)	Same problem in TIA V14 upd1 on Windows 7 64bit in VirtualBox. The WinCC runtime window shows some of the content from the TIA windows behind it. I had to tick the Enable 3D accelleration in Virtual Machine Settings and reinstall VirtualBox Guest Additions, tick 3D Accelleration (experimental) under the installation, and select No to install basic Direct3D support when asked. After a reboot the problem is solved.
	Anders Jorsal Software and Development Manager ALSMATIK A/S www.alsmatik.dk
Suggestion To thank Quote Answer
This contribution was helpful to 4 thankful Users DonSebas poppb Asystema Bayandin

2/6/2017 9:51 AM	Rate (0)
DonSebas Regular Member Joined: 3/19/2012 Last visit: 11/27/2024 Posts: 6 Rating: (2)	I have had the same issue, was running TIA V14 upd1 on win7 Pro in VMWare. In my case I only checked the 3d acceleration in the display menu, and everything worked like it used to do.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users guilda

2/12/2019 4:50 PM	Rate (0)
rokiseroman Posts: 24 Rating: (0)	Hello everyone. I have the same problem with starting simulator in v.14.1 on Windows 10. I just change device version to 13, compile and then change to 14.1. Then everything ok
rokiseroman Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on