Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Technology object TO_positioningAxis with S120 (CU310) and external encoder.

Created by: gigi_plc at: 10/19/2018 3:58 PM (13 Replies)

Rating (0)

Thanks 3

Result pages:: |; 1 | 2; |

14 Entries

Entries per page: 10 | all

10/19/2018 3:58 PM	Rate (0)
gigi_plc Bronze Member Joined: 12/14/2011 Last visit: 11/6/2024 Posts: 166 Rating: (14)	Hi to all, i am working with an application that have: - CPU 1515F - S120 drive with CU310 - External incremental encoder connect to SMC30 in drive CLIQ - TO_PositioningAxis in the program with TIA portal V15 Actually i am able to work if i use telegram standard 3 and telegram 81 in the hardware configuration. But if i try to use telegram 106 without the 81 in the technology object there is the error "configuration error" but not more information. Which is the correct telegram configuration for this application? Many thanks. Attachment Immagine1.png (510 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users AutoGen_9113071 uyarfevzi

10/19/2018 4:20 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 11/8/2024 Posts: 5935 Rating: (815)	Hello, when you try Telegram 106 the encoder needs to be assigned as 2nd encoder of the axis and not as external encoder DO (settings in STARTER). Please send a screenshot of your telegram configuration mask in STARTER. Please also note that you should configure IRT communication in that case and configure the PROFINET topology in the topology view ot TIA.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

10/19/2018 4:50 PM	Rate (0)
gigi_plc Bronze Member Joined: 12/14/2011 Last visit: 11/6/2024 Posts: 166 Rating: (14)	Hi, when i use telegram 106 i configure the external encoder as second encoder. Look at the picture. The topology and the IRT is configurated correctly. If i use telegram 81 and telegram 105 instead of standard 3 i have the same error. I replace the 105 and put standard 3 and all is ok. This is strange why with standard 3 it is ok and 105 no. Attachment Immagine10.png (496 Downloads)

Suggestion To thank Quote Answer

10/20/2018 10:19 PM	Rate (0)
zako_ Gold Member Joined: 5/22/2012 Last visit: 3/24/2022 Posts: 895 Rating: (67)	Hello, I configured it and can translate it without fault - see attached bitmap. Zako Attachment S71515F_withCU310PN.JPG (514 Downloads)

Suggestion To thank Quote Answer

10/22/2018 6:31 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22445 Rating: (3029)	Hello, do you have a screen of the configuration error message? Regards Christoph

Suggestion To thank Quote Answer

10/22/2018 7:09 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 11/8/2024 Posts: 5935 Rating: (815)	Hello, this maybe sounds like a problem with IRT as you have problems with telegrams 105 and 106 and not when using telegram 3. Did you assign the telegram to the MC Servo OB for synchronization? Please compile the PLC and send a screenshot of the messages.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

10/22/2018 9:16 AM	Rate (0)
gigi_plc Bronze Member Joined: 12/14/2011 Last visit: 11/6/2024 Posts: 166 Rating: (14)	Hi to all and thanks for your interest, here the picture with my hardware configuration, later a send to you the picture with the generic error ("configuration error") in the technology object. In the left side of the picture you can see that i am using also two measuring input with telegram 391 in isochronous mode. I don't know if this function can be the real problem with telegram 105 or 106. With telegram 3 it is working well. However if i rebuilt all, there are no error. The error coming out after i transfer the configuration to the plc and try to move the motor. Many thanks Attachment Immagine_b1.png (461 Downloads)

Suggestion To thank Quote Answer

10/22/2018 9:48 AM	Rate (0)
gigi_plc Bronze Member Joined: 12/14/2011 Last visit: 11/6/2024 Posts: 166 Rating: (14)	Here the error... as you can see i have no more information about the error.. I only know that i have to use telegram standard 3 otherwise i can't work with my application. Attachment Immagine_b3.png (297 Downloads)

Suggestion To thank Quote Answer

10/22/2018 9:57 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22445 Rating: (3029)	Hello, in the last screen select a device in the drop down list in the lower part of the windows. In the moment "(No device selected)" so no information displayed. You can also look in the diagnostic puffer of the plc for some alarms regarding the configuration error. Have you change the Telegram at all positions? You must change it in HWConfig/Starter and in the technologyobject. Regards Christoph

Suggestion To thank Quote Answer

10/22/2018 10:21 AM	Rate (0)
gigi_plc Bronze Member Joined: 12/14/2011 Last visit: 11/6/2024 Posts: 166 Rating: (14)	Hi, Here the alarm: MC Fatal Alarm 101: PLC_1 M301_Profila: Errore di configurazione. (La configurazione dell'encoder non è adatta alla procedura DSC. Valore non consentito in Sensor[1].Existent e/o Sensor[1].Interface.Address[In, Out].RID e/o Sensor[1].Interface.Number.) The encoder configuration is not suitable for the DSC procedure, value not possible in Sensor[1].Existent e/o Sensor[1].Interface.Address[In, Out].RID e/o Sensor[1].Interface.Number. What't does it means? Many thanks Attachment Immagine_b4.png (303 Downloads)

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on