With KTP700 version 16.0.0 simulation works.

But what i need to do to make simulation on KTP 600? It is version 12.0.0.

artur2705

 Hello,

I'm just Artur, without 2705 )))

No, it is just a test. I learn tia portal. There are two inputs and output.

Wizard

Hello artur2705,

Is this an old project?

When you make a new project, where you choose a S7-1200 CPU and a KTP700 Basic panel.

Is it possible to simulate this project?

Best regards,

Wizard

 

 It means, that i must install DVD 3 of legacy panel images, and update firmware of panel from that dvd?

0_Einstein

Update the firmware on the KTP600.

artur2705

 With KTP700 version 16.0.0 simulation works.

But what i need to do to make simulation on KTP 600? It is version 12.0.0.

artur2705

 Hello,

I'm just Artur, without 2705 )))

No, it is just a test. I learn tia portal. There are two inputs and output.

Wizard

Hello artur2705,

Is this an old project?

When you make a new project, where you choose a S7-1200 CPU and a KTP700 Basic panel.

Is it possible to simulate this project?

Best regards,

Wizard

 

 Wait. I found one chat here:

The KTP600 is a first generation KTP-type HMI. The last firmware version for KTP600 is 12.0.0.0. There is no firmware upgrade that can be performed.

I can confirm that a simulation of S7-1200 and KTP600 on TIA V15.1 is a problem. The simulated KTP600 seems to establish a link with the simulated S7-1200, but after 15sec the link is broken. The S7-1200 never shows that a connection is made.

The KTP600 might not simulate.

So it is answer on all my questions :)

Thanks to all of you for help!

Artur

0_Einstein

Update the firmware on the KTP600.

artur2705

 With KTP700 version 16.0.0 simulation works.

But what i need to do to make simulation on KTP 600? It is version 12.0.0.

artur2705

 Hello,

I'm just Artur, without 2705 )))

No, it is just a test. I learn tia portal. There are two inputs and output.

Wizard

Hello artur2705,

Is this an old project?

When you make a new project, where you choose a S7-1200 CPU and a KTP700 Basic panel.

Is it possible to simulate this project?

Best regards,

Wizard

 

 

 But KTP400 is also rev 16.0

0_Einstein

Ahh, that is a good reason to not use KTP600 rev 12.0

 With ABSOLUTE ADDRESSING the resault is the same - no simulation

0_Einstein

Update the firmware on the KTP600.  An alternative is to use ABSOLUTE ADDRESSING for all HMI related tags.

I think v12 was around the time when KTP600's were not quite ready for symbolic tags (error free anyhow).  Physical KTP's back then would work great with absolute addresses.  But, symbolic addresses, it would work sometimes. But once it did not work just once, it quite working until it was power cycled.

artur2705

 With KTP700 version 16.0.0 simulation works.

But what i need to do to make simulation on KTP 600? It is version 12.0.0.

artur2705

 Hello,

I'm just Artur, without 2705 )))

No, it is just a test. I learn tia portal. There are two inputs and output.

Wizard

Hello artur2705,

Is this an old project?

When you make a new project, where you choose a S7-1200 CPU and a KTP700 Basic panel.

Is it possible to simulate this project?

Best regards,

Wizard