Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Can not transfer project to OP73

Created by: Tomy Master at: 4/12/2010 10:52 PM (5 Replies)

Rating (0)

Thanks 0

6 Entries

4/12/2010 10:52 PM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 5/28/2024 Posts: 914 Rating: (40)	Dear all. I am now trying to transfer a project from WinCC Flexible 2008 to OP73 via RS232/PC-PPI cable (6ES7 901-3CB30-0XA0). I have made the following settings in the "set PG/PC interface": 1- in the access point of application, i set it to WinCC MPI --> PC/PPI cable (PPI). 2- Local connection to COM1. And in the transfer window of WinCC software, I have set the following: 1- Serial RS232/PC-PPI multi master. 2- Baud rate to 115200. 3- COM1. And on the cable I have set the baud rate to 115200 (only dip switch1 & 2 "on"). And on the panel I have made the serial channel 1 "enabled, and I have entered transfer screen. Yet when I do the transfer job, the output window shows me that a connection to the panel can not be established. you can refer to the attached file. Just tell, what should I change to achieve project transfer, is it on the cable, on the panel or in the WinCC? Really I have tried a lot of possibilities, and I need some help. Thank you in advance. Tomy the Master. Attachment OP73_Transfer_Failure_01.GIF (160 Downloads)
	Aim Higher
Suggestion To thank Quote Answer

4/13/2010 5:14 AM	Rate (0)
UMENCHO Diamond Expert Joined: 3/21/2006 Last visit: 11/1/2024 Posts: 10229 Rating: (1181)	Hello Tomy, Look at You can use the following RS232/PPI Multi Master cables for downloading a project: Order Number: 6ES7901-3CB30-0XA0 The RS232/PPI Multi Master cable (with 8 DIP switches) can be used if DIP switch number 5 is set to PPI/freeport ("0"). The cable must be dead for it to accept the change. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

4/13/2010 9:18 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 11/5/2024 Posts: 8766 Rating: (1170)	Dear Tomy, In addition, have a look at this link: how can you transfer a WinCC fleixble project serially to a panel? Best regards, Wizard

Suggestion To thank Quote Answer

4/13/2010 3:33 PM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 5/28/2024 Posts: 914 Rating: (40)	Yes my friends... I havedone all your recommendations, and the problem still exsits. please, I need help. Tomy.
	Aim Higher
Suggestion To thank Quote Answer

4/15/2010 6:29 PM	Rate (0)
Tomy Master Gold Member Joined: 5/4/2009 Last visit: 5/28/2024 Posts: 914 Rating: (40)	Dear Friends... Another thing, when download procedure is being performed, the two LEDS, RX & TX are blinking but at the end the process fails!!!! Tomy.
	Aim Higher
Suggestion To thank Quote Answer

9/22/2017 11:06 AM	Rate (0)
zromVIT Advanced Member Joined: 3/1/2009 Last visit: 8/16/2024 Posts: 6 Rating: (0)	Have the same trouble) How did you resolve this issue?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on