SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

F-PM-E shuttdown-down via F-CPU

6/30/2023 8:53 AM	Rate (0)
AutoGen_7826936 Posts: 7 Rating: (0)	Hi, I have a Failsafe Power Module (F-PM-E) for ET200sp (6ES7136-6PA00-0BC0) in the same potencial group than Standart DQ modules. According to the manual, when an error is detected or when the F-input of the F-PM-Eis switched-off, the bus power (P1-P2) will shutdown all the modules of the same potencial group. https://support.industry.siemens.com/cs/pt/en/view/78645796 However, the following video of the Siemens Youtube Channel is saying that shutting-down the potencial group is also posible from the F-CPU (in my case 1515F), via Profisafe. But I don't know how to do that... Could you help me with this? https://www.youtube.com/watch?v=aXmMCV1dHl4 Best regards.
AutoGen_7826936 Posts: 7 Rating: (0)	Last edited by: Jen_Moderator at: 06/30/2023 11:30:09 Link optimized. Video embedded.
Suggestion To thank Quote Answer

6/30/2023 7:01 PM	Rate (0)
CaOd Platinum Expert Joined: 5/6/2010 Last visit: 9/8/2025 Posts: 2031 Rating: (284)	Hello, you can switch the output of the PM-E-module with the output address of the module (X.0 ). If you have the output starting address e.g. 4 then is your output the DQ 4.0. With this address you can switch on/off the PM-E-module voltage bus P1 and P2. The description you can find at the manual oft the PM-E-module at chapter 3.1 -terminal assignment - digital output and at chapter 4.3 - address space. Hope this is what you need. regards CaOd

Suggestion To thank Quote Answer

7/3/2023 5:04 AM	Rate (0)
AutoGen_7826936 Posts: 7 Rating: (0)	Ok, thank you, I will check it. Best Regards!!
AutoGen_7826936 Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

7/13/2023 5:46 PM	Rate (0)
AutoGen_7826936 Posts: 7 Rating: (0)	Hi again, I have been thinking about that this output is not wired to anything... Could this be a problem?? I have "Activated" the output to be able to use it in the Fail-Safe sequence, and I have disabled the dark test, the light test and the wire break diagnosis. Is it enough to work with this no-wired FS-output?? Thanks Attachment f-pm-e.jpg (520 Downloads)
AutoGen_7826936 Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

7/17/2023 6:06 PM	Rate (0)
CaOd Platinum Expert Joined: 5/6/2010 Last visit: 9/8/2025 Posts: 2031 Rating: (284)	Hello, yes it should work . You switch the power supply to the right base units (grey) at the internal connection at the base unit. Please check that you wire the M at the PM-E module two times. regards CaOd

Suggestion To thank Quote Answer

Share this page:

Share this page on...