Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Problem uploading pcp file to sinumerik 810t

Created by: ticko at: 2/4/2012 10:07 PM (32 Replies)

Rating (1)

Thanks 4

Result pages:: |; 1 | 2 | 3 | 4; |

33 Entries

Entries per page: 10 | 20 | all

2/4/2012 10:07 PM	Rate (0)
ticko Posts: 7 Rating: (0)	Hello, I have a CNC machine with Sinumerik 810t GA3, which had bad batteries and data were lost. I have a backup of TEA1, TEA2, PCP and PCA. I replaced the batteries and followed instructions how to upload data, but i have the following problem. I successfully uploaded TEA1 and TEA2 files. But when i want to upload PCP file, the transmission is interrupted after a few bytes transferred (195 bytes). It happens every time. I also tryed slower speeds (300), and the transmission stoped after 73 bytes. If i try to upload other files it works. The problem is only with PCP data. Does anybody have a clue, what could be wrong? Thank you. Regards, Matic
ticko Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/5/2012 7:57 PM	Rate (0)
Pee El Sea Gold Member Joined: 1/19/2008 Last visit: 10/2/2024 Posts: 992 Rating: (63)	Hi, Are you loading it in initial clear mode ?. Pee

Suggestion To thank Quote Answer

2/6/2012 9:49 PM	Rate (0)
ticko Posts: 7 Rating: (0)	Yes, I am doing it in initial clear mode. I was following the manual from Siemens about reloading machine data. As I have read inthis thread,it might be corrupted PCP file... Any suggestions?
ticko Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/7/2012 8:57 AM	Rate (0)
Pee El Sea Gold Member Joined: 1/19/2008 Last visit: 10/2/2024 Posts: 992 Rating: (63)	Hi, If you look at the file in a text editor it should obviously start with %PCP and then long lines of code such as D80230A1 etc etc. It is a hex code dump of the plc. Upload it if your not sure and I'll have a look This file usually goes in OK it's the alarm text file that everybody has problems with. Pee

Suggestion To thank Quote Answer

2/8/2012 4:19 PM	Rate (0)
rezahashemi Posts: 10 Rating: (0)	Dear ticko could you send me pcp file?
rezahashemi Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

2/10/2012 11:56 AM	Rate (0)
ticko Posts: 7 Rating: (0)	Hi, file starts with '% P C P' and not with '%PCP'. See the attachment. Do you think this is the problem? Regards, Matic Attachment SPT.zip (975 Downloads)
ticko Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/13/2012 10:18 PM	Rate (0)
Jefke Advanced Member Joined: 9/15/2009 Last visit: 7/23/2024 Posts: 25 Rating: (0)	are you using XP? I expierienced many problems with PC(or PG)with XP. With a PC with WIN98 never problems (only for PCP, other serial transmission under XP is no problem)

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users TheySaidMyNickNam...

2/13/2012 10:38 PM	Rate (0)
ticko Posts: 7 Rating: (0)	Hi, yes I tried both, Win XP and 98. In XP i also had problems with TEA1 and TEA2 which didn't upload completely. Then I switched to Win 98, TEA1 and TEA2 were uploaded without problems but PCP data not. Then i tought it it must be a communication problem, so i tried few different connection parameters. I set lower baud rate on both PC and CNC, all without success. PCP data transfer stops after few bytes transmitted. But i can transmit cnc programs and other data without problems via RS232, so i think the problem is not computer or OS related. Regards, Matic
ticko Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

4/16/2014 7:33 AM	Rate (0)
Primoz12 Posts: 1 Rating: (0)	I have exactly the same problem with my Siemens 810m GA2. I have been trying several different things, but after 2688bytes siemens stop receiving file containing %PCP parameters. If I furter press start transmit button, the transmission is continued, not as pcp parameters but in a separate file. I dont know if it is even possible to transmit his.
Primoz12 Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

4/16/2014 4:20 PM	Rate (0)
Ekalavya Posts: 2964 Rating: (484)	Primoz12 I have exactly the same problem with my Siemens 810m GA2. I have been trying several different things, but after 2688bytes siemens stop receiving file containing %PCP parameters. If I furter press start transmit button, the transmission is continued, not as pcp parameters but in a separate file. I dont know if it is even possible to transmit his. Hello, Try clearing the NC and PLC by pressing the eye button softkey and check. Regards, Prakash
Ekalavya Posts: 2964 Rating: (484)
Suggestion To thank Quote Answer

Result pages:: |; 1 | 2 | 3 | 4; |

33 Entries

Entries per page: 10 | 20 | all

|

Share this page:

Share this page on...

Follow us on