SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Motor not run after given enable signal

5/19/2010 12:31 PM	Rate (0)
haque_1981 Posts: 19 Rating: (0)	Dear sir I am facing a problem in simovert masterdrives VC.After enable run signal frequency does not outputting,so motor not rotate.This drives run with pulse encoder feedback.I have given analog signal 2.5vdc but PMU display is 0000 in parameter r000. Please give me solution about this matter. Thanks Haque
haque_1981 Posts: 19 Rating: (0)
Suggestion To thank Quote Answer

5/19/2010 1:10 PM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 8/5/2024 Posts: 1976 Rating: (477)	Wait for few seconds after giving start command and check if you are getting any fault or alarm If you are not getting any fault or alarm, check your setpoint channel. Regards, Devesh
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

5/20/2010 5:33 AM	Rate (0)
haque_1981 Posts: 19 Rating: (0)	Dear Devesh This drive is simovert masterdrives vc,software version 3.4. System run in close-loop operation. Parameter P095=10 Async./sync. IEC (International standard) P100=4 speed control with tachometer (n control). P130=11 Pulse encoder Digital input signal use for speed compensation P573=B0020 MOP UP P574=B0022 MOP DOWN In this condition i enable drive, Display r000 is 0000 Hz I have increase pot voltage about 2.5v analog input terminal 15 & 16. r000 is 0000 Hz also. Analog input selection switch S3 in off position. Is it correct parameter for close-loop operation? If not correct. Please somebody guide me. Regards Haque
haque_1981 Posts: 19 Rating: (0)
Suggestion To thank Quote Answer

5/20/2010 6:49 AM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 8/5/2024 Posts: 1976 Rating: (477)	From where you want to run drive? If you want to run it from Analogue Input then no need to set P573 and P574 You have to set P443 for setpoint and in this case value should be 11 Regards, Devesh
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users haque_1981

5/20/2010 9:11 AM	Rate (0)
haque_1981 Posts: 19 Rating: (0)	Dear Devesh Thanks for your suggestion.Problem has solved. [schnippschnapp] Haque New question is splitted to analog input at cuvc terminal X102 15 is ov but output frequency 1.95Hz..
haque_1981 Posts: 19 Rating: (0)	Last edited by: O_Moderator at: 5/21/2010 12:28 PM
Suggestion To thank Quote Answer

10/11/2019 8:20 AM	Rate (0)
mosi_0333 Posts: 19 Rating: (0)	Dear vithani. Can i have ur email
mosi_0333 Posts: 19 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...