Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

F035 Fault reset simovert vc

Created by: dnk185 at: 7/24/2014 10:30 PM (7 Replies)

Rating (0)

Thanks 4

8 Entries

7/24/2014 10:30 PM	Rate (0)
dnk185 Posts: 5 Rating: (0)	Hello all, I created this fault some how using the op1s now can not get it to go away. I think im close to figuring out how to reset this fault by reading the manual. I think you reset it using P575? It has parameter values 0: not allowed = 18 1: no external fault = 18 So what parameters do I change to fix this issue? Sorry, I'm farily new to this drive. simovert vc frequenzumrichter VFD. Thanks
dnk185 Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/25/2014 2:47 PM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 11/12/2024 Posts: 1505 Rating: (326)	Hi, at the moment, if Digital Input 5 (18) is low, then you will get the F035 External Fault. If you didn't need the Digital Input to trigger this fault, you can set P575.001 = 1. That should then allow the F035 fault to be acknowledged. Make sure that this was not required in the first case, as this may have been some kind of "safety" interlock. Regards, Graeme

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users AutoGen_547181

7/30/2014 9:02 PM	Rate (0)
dnk185 Posts: 5 Rating: (0)	Worked great for me. Thank you
dnk185 Posts: 5 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Graeme

5/8/2018 3:14 PM	Rate (0)
ETOVLAD Posts: 2 Rating: (0)	Hello, I have pretty same issue. When I start the Drive immediately appears F035. I have couple questions : can you send procedure how can I find P575 or where can I find P575? Thanks in advance!
ETOVLAD Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

5/9/2018 6:14 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/14/2024 Posts: 8092 Rating: (878)	Hello, P575 is BICO parameter for selecting binector for tripping in case external fault signal is to be read, it is control word bit 15. So check the parameter back up to know the source of P575 binector or see r550 status on display if control word bit 15 is low or high. For details please refer attached sheet. Attachment Simovert r550 status display.pdf (755 Downloads)

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users ETTAHRIOUI AutoGen_547181

5/9/2018 8:45 AM	Rate (0)
ETOVLAD Posts: 2 Rating: (0)	Thanks a lot!
ETOVLAD Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

9/29/2018 7:54 AM	Rate (0)
zia07 Posts: 7 Rating: (0)	We had fault F150 on our drive, 1500kw, cooling fan at rectifier side was stuck up and fuse(7A) was blown on power supply card. replaced fuse and fan, started normal
zia07 Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

7/12/2024 12:21 PM	Rate (0)
AutoGen_547181 Joined: 7/12/2024 Last visit: 7/13/2024 Posts: 1 Rating: (0)	Hello, may I ask if the 6SE71 frequency converter is reporting F035 fault during operation, but the parameters are locked by password and cannot be viewed. How should I solve it? Can the external fault input 1 of F035 be shielded by changing the wiring at the x101 terminal of CUVC?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on