Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

Micromaster 440 problem

Created by: Keromieage at: 9/4/2019 1:32 PM (22 Replies)

Rating (10)

Thanks 0

Result pages:: |; 1 | 2; |

23 Entries

Entries per page: 10 | 20 | all

9/4/2019 1:32 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	Hello I got micromaster 440 It's working fine but in random times i got problem It got 2 l.e.d lamps not a screen The green lamp flashes I found that is overvoltage problem The 3 ,phase is ok And the motor is ok The brake is installed and it's ok Could any one help me
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 1:36 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	The first green lamp flashes The second lamp is off That what shown on sdp when i got that error Attachment Screenshot_2019-09-04-13-34-36-64.png (488 Downloads)
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:19 PM	Rate (1)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 8/5/2025 Posts: 1518 Rating: (327)	Hi, what do you mean by "brake", motor brake, or Dynamic brake with a resistor mounted somewhere in/or on your panel? Is this a new fault, or has it been intermittent from new? If the drive occasionally overvoltages, then it's possible that the motor is regenerating i.e. during deceleration and the drive cannot dissipate the excess power. To protect the hardware, the drive trips. With only an SDP, you will struggle to resolve this issue, you need at the very least, a BOP, or better the free software: Starter and a PC connection kit to diagnose the drive. Regards, Graeme

Suggestion To thank Quote Answer

9/4/2019 4:33 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:34 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	I have upload. A video It's new error just started to happens this week Dynamic one not motor brake And it happens some time on the start up without even running the motor
Keromieage Posts: 11 Rating: (0)	Last edited by: Keromieage at: 09/04/2019 16:36:23 Last edited by: Keromieage at: 09/04/2019 16:39:37
Suggestion To thank Quote Answer

9/4/2019 4:38 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	An over Voltage fault, is cause by a high DC Link Voltage, which can be created by: High supply Voltage or Regeneration from a high inertia load As you have a mechanical brake in the system, I would first consider the operation of the brake for: 1/ Serviceability, brake wear or adjustment. 2/ The brake operating system, is this the Micro Master or the a PLC. The Micromaster is the most reliable component for operating the brake. 3/ Also consider the ramp down time, has this been reduced? 4/ Has the mass of the system been increased? Note. If you do not have a keypad available, diagnosis for this problem will be difficult. Do you have a PC available with the STARTER software diagnosis tool installed?
	Last edited by: tractor at: 09/04/2019 16:39:32 Tractor
Suggestion To thank Quote Answer

9/4/2019 4:42 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor An over Voltage fault, is cause by a high DC Link Voltage, which can be created by: High supply Voltage or Regeneration from a high inertia load As you have a mechanical brake in the system, I would first consider the operation of the brake for: 1/ Serviceability, brake wear or adjustment. 2/ The brake operating system, is this the Micro Master or the a PLC. The Micromaster is the most reliable component for operating the brake. 3/ Also consider the ramp down time, has this been reduced? 4/ Has the mass of the system been increased? Note. If you do not have a keypad available, diagnosis for this problem will be difficult. Do you have a PC available with the STARTER software diagnosis tool installed? No i don't have a keypad Its not mechanical brake This just start to happens this week Even if the motor is not running The motor is working fine and it's got this error in random times Did u watched my video?
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:43 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	From the video it looks like an Over Voltage. You do need a software diagnosis tool to diagnose this? What is the motor doing in this application?
	Tractor
Suggestion To thank Quote Answer

9/4/2019 4:46 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	If the fault happens whilst the drive is stopped then it must be a power supply problem?? It may appear that the supply is ok, using a meter, do you have a means of looking at the supply waveform? Sorry about this, but it needs some test equipment to diagnose what is causing this fault.
	Tractor
Suggestion To thank Quote Answer

9/4/2019 4:48 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor From the video it looks like an Over Voltage. You do need a software diagnosis tool to diagnose this? What is the motor doing in this application? It's running a Production cartoon belt But is high voltage error can happend even the motor did not running?
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:49 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor If the fault happens whilst the drive is stopped then it must be a power supply problem?? It may appear that the supply is ok, using a meter, do you have a means of looking at the supply waveform? Sorry about this, but it needs some test equipment to diagnose what is causing this fault. I got micromaster 420 near this 440:and it works fine Without anyproblem so i don't think there problem in the power
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:50 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	I have the video, the 'Brake' is a braking resistor, not a mechanical brake, as I assumed. The braking resistor is switched in by the drive in order to dissipate the regenerated energy from a high inertia load during ramp down. As I suggested, this may be a supply issue.
	Tractor
Suggestion To thank Quote Answer

9/4/2019 4:52 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor I have the video, the 'Brake' is a braking resistor, not a mechanical brake, as I assumed. The braking resistor is switched in by the drive in order to dissipate the regenerated energy from a high inertia load during ramp down. As I suggested, this may be a supply issue. Therea 420 micromaster and it working fine in the same machine panel
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 4:56 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	Can you measure the Voltage across, B+/DC+, and DC- ? This should be less than 670 Volts, from memory?? After this, it may be the drive is failing and needs replacing??
	Tractor
Suggestion To thank Quote Answer

9/4/2019 5:02 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor Can you measure the Voltage across, B+/DC+, and DC- ? This should be less than 670 Volts, from memory?? After this, it may be the drive is failing and needs replacing?? It's 520v between b+ / DC+ and DC -
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 5:06 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	If this happens while the drive / motor is at standstill, it may be a supply problem. But, the MM420 on the same supply is OK, then it may be a defective drive. Can you replace it?
	Last edited by: tractor at: 09/04/2019 17:06:34 Tractor
Suggestion To thank Quote Answer

9/4/2019 5:07 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	520 Volts DC is OK, and should not create an Over voltage.
	Tractor
Suggestion To thank Quote Answer

9/4/2019 5:09 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor If this happens while the drive / motor is at standstill, it may be a supply problem. But, the MM420 on the same supply is OK, then it may be a defective drive. Can you replace it? Yes it's just happened like 3-4 times in the day While the mm420 on the same system and it's working fine without any error I think it may be damaged or something like that Is there somewhere i can got. A new mm440 at egypt ?
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/4/2019 5:18 PM	Rate (1)
Tractor Gold Expert Joined: 3/27/2008 Last visit: 9/14/2025 Posts: 1216 Rating: (148)	The MM440 is not now manufactured, but I guess there will be repair agents in Egypt. Or EBay may be able to help? You will also need someone with the STARTER software installed on a PC, to transfer the configuration to a new MM440. If you cannot find a suitable MM440, the replacement will be a Sinamics drive (G120 Type), and as the parameters will not transfere from the MM440 to the Sinamics drive the system will need to be re-commissioned.
	Tractor
Suggestion To thank Quote Answer

9/4/2019 5:20 PM	Rate (0)
Keromieage Posts: 11 Rating: (0)	tractor The MM440 is not now manufactured, but I guess there will be repair agents in Egypt. Or EBay may be able to help? You will also need someone with the STARTER software installed on a PC, to transfer the configuration to a new MM440. If you cannot find a suitable MM440, the replacement will be a Sinamics drive (G120 Type), and as the parameters will not transfere from the MM440 to the Sinamics drive the system will need to be re-commissioned. Ok thanks u sir for ur time 👍 Iam going to search for the Siemens agents in Egypt
Keromieage Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on