Skip to Content

Register Login

Default Header

(header konnte nicht geladen werden)

Navigation

MM440 Factory settiing problem

Created by: Arijit at: 10/31/2011 9:55 AM (23 Replies)

Rating (2)

Thanks 2

Result pages:: |; 1 | 2 | 3; |

24 Entries

Entries per page: 10 | 20 | all

5/1/2012 1:51 AM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 8/5/2025 Posts: 1518 Rating: (327)	Hi, can you give us the parameter values for: P0003 = ? P0010 = ? P3900 = ? P0927 = ? Regards, Graeme

Suggestion To thank Quote Answer

5/1/2012 1:36 PM	Rate (0)
Amit3545 Experienced Member Joined: 2/27/2012 Last visit: 9/29/2024 Posts: 17 Rating: (0)	Hiii Graeme, P0003 = 3 P0010 = 2 P3900 = 0 P0927 = 15 But after putting P0003 to 3 when i am trying to make the parameter P0010 to any value like 1,30 etc.It is not changing..It is remaing on 2... regards, amit

Suggestion To thank Quote Answer

5/1/2012 9:24 PM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 6/7/2025 Posts: 1977 Rating: (479)	Amit3545 Hiii Graeme, P0003 = 3 P0010 = 2 P3900 = 0 P0927 = 15 But after putting P0003 to 3 when i am trying to make the parameter P0010 to any value like 1,30 etc.It is not changing..It is remaing on 2... Have you checked Parameter r200 & P201 this both should be same For 2.2 KW drive (MLFB:6SE6440-2AB22-2BAx) Code should be 56 Please verify this Regards Devesh
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Vladsat Lebs16

7/8/2013 11:15 AM	Rate (0)
mpradhan Posts: 3 Rating: (0)	Sir,what is the solution of factory reset p0010=2 not reset.
mpradhan Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

7/8/2013 1:00 PM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 9/3/2025 Posts: 4522 Rating: (843)	mpradhan Sir,what is the solution of factory reset p0010=2 not reset. Hello, Please openMarcjan'sattached picture in this thread (5th post). [IMG]/tf/WW/en/postattachments/download?attachmentId=23578[/IMG] Hope this helps.
	Last edited by: Ayman Elotaify at: 7/8/2013 1:30 PM Ayman Elotaify
Suggestion To thank Quote Answer

7/8/2013 2:56 PM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 6/7/2025 Posts: 1977 Rating: (479)	mpradhan Sir,what is the solution of factory reset p0010=2 not reset. Have you read complete thread? Have you tried setting P10 to 0 from 2 as Graeme said?? Graeme Hello, it is not clear from your description if you have tried to put P0010 back into no commissioning mode. i.e. P0010=0. You absolutely cannot change from P0010=2 to P0010=30 without first changing to the no commissioning mode P0010=0. Regards, Graeme
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

7/25/2013 2:27 PM	Rate (0)
Bassam2014 Regular Member Joined: 4/28/2013 Last visit: 7/4/2024 Posts: 10 Rating: (0)	Dear sir you have to check if P0011 value equal to P0013 value Regards

Suggestion To thank Quote Answer

7/27/2013 4:25 AM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 6/7/2025 Posts: 1977 Rating: (479)	Bassam2014 Dear sir you have to check if P0011 value equal to P0013 value Regards YOU DONT NEED THIS FOR FACTORY RESET REGARDS, DEVESH VITHANI
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

9/24/2013 12:11 PM	Rate (0)
ndthang_hd Posts: 1 Rating: (0)	My inverter not setting too, P0010=2, P3900=0, r0200=P0201=0, r0203=0, P0970=0. Can you help me, please?
ndthang_hd Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

9/24/2013 4:19 PM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hi you have tried says Marcjan? factory-reset.JPG

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on