Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Problem with dust protocol

Created by: RAJAKARTHIKEYAN at: 7/28/2015 10:14 AM (10 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

7/28/2015 10:14 AM	Rate (0)
RAJAKARTHIKEYAN Member Joined: 3/27/2014 Last visit: 8/4/2021 Posts: 5 Rating: (0)	hi I am facing the problem with dust protocol , ---------------------------------------------------------------------------------------------------- Split from T400 download with DUST1. Attachment Screenshots.zip (601 Downloads)
	Last edited by: Min_Moderator at: 7/28/2015 3:48:13 PM New subject after splitting
Suggestion To thank Quote Answer

7/28/2015 12:33 PM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (280)	Hello. What did you try to do with DUST1? Do you have any problem with DUST1 in 'Setting the PG/PC Interface'? I think 'Display accessible nodes' don't work with DUST1 protocol.

Suggestion To thank Quote Answer

7/28/2015 5:33 PM	Rate (0)
miami Platinum Expert Joined: 8/31/2005 Last visit: 10/22/2024 Posts: 2198 Rating: (328)	To go online on a T400, you must have selected DUST1 (and COM1 or COM2) in the PC/PG Interface configuration and click on the "Online-Switch" in CFC.

Suggestion To thank Quote Answer

9/1/2016 8:00 AM	Rate (0)
as.rahgozar Posts: 4 Rating: (0)	hi dear sir could u find any solution to install dust1 protokoll? tnx
as.rahgozar Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

9/1/2016 8:14 AM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (280)	as.rahgozar could u find any solution to install dust1 protokoll? Hello. What problems do you have with DUST1? Have you installed D7-SYS software?

Suggestion To thank Quote Answer

9/1/2016 8:22 AM	Rate (0)
as.rahgozar Posts: 4 Rating: (0)	hello I have been trying to connect to a T400 via DUST1, and have run into an issue where Add/Remove within PG/PC interface does not successfully install DUST1. When I select DUST1 on the left hand side and click install the right hand side flickers and refreshes, but does not actually add DUST1. i have installed d7sys 6.2 and upgraded it into d7sys 6.2 sp3, however it didn't work!
as.rahgozar Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

9/1/2016 8:31 AM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (280)	What versions of Step 7 and CFC do you have? There is a problem with DUST1 installation in combination of Step 7 V5.4 SP3 (and I think higher versions) and D7-SYS V6.2 SP3. You need in this case HF3 for D7-SYS V6.2 SP3.

Suggestion To thank Quote Answer

9/1/2016 10:54 AM	Rate (0)
as.rahgozar Posts: 4 Rating: (0)	thank u so much bud i need d7 6.2 not d7 6.2 sp3 what can i do for d7sys 6.2 to install dust1 protocol?
as.rahgozar Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

9/1/2016 11:19 AM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (280)	You still didn't answer what versions of Step 7 and CFC do you have? Previously you have wrote: as.rahgozar i have installed d7sys 6.2 and upgraded it into d7sys 6.2 sp3, however it didn't work! What version of D7-SYS you have?

Suggestion To thank Quote Answer

9/1/2016 11:31 AM	Rate (0)
as.rahgozar Posts: 4 Rating: (0)	My d7 is 6.2 and with PG M & PG M2 it correctly installs dust1 but for PG M4 it doesnt work i tried to upgrade d7 to sp3 maybe it works, but it didnt!
as.rahgozar Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on