Navigation

indirect addressing

Created by: Roby at: 12/1/2010 10:12 AM (8 Replies)

12/1/2010 10:12 AM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Hallo, friends I have never used indirect addressing, and I have some difficulty.... To make the diagnosis,i need to see the status of the entire range of inputs of the plc. I want to do this type in a word from the operator panel, the number of byte whichi want to show its status. example: if I write 10, i want to see thebits ranging from 10.0 to 10.7 if I write 100, i want to see thebits ranging from 100.0 to 100.7 naturally on the operator panel will field the word for the number of byte of input and result fields of eight bits. if I use the comparison, i mustwrite so many comparisons as the number of bytes of address, making the program long and hard. can be done with indirect addressing ... someone give me a hand? Thank you Roby
	Last edited by: Roby at: 12/1/2010 10:39 AM Last edited by: Roby at: 12/1/2010 10:23 AM Last edited by: Roby at: 12/1/2010 10:20 AM Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

12/1/2010 11:47 AM	Rate (1)
sfa Posts: 70 Rating: (3)	Hi Roby The solution is quite simple when you know how to do it :-) See attached example I use SLD 3 to point at a byte (4 will point at a word and 5 at dwords) finally you must store the result in a byte : T MBxx /søren Attachment FC1.jpg (171 Downloads)
sfa Posts: 70 Rating: (3)	Last edited by: sfa at: 12/1/2010 11:49 AM Forgot to tell you that it is important that you check for valid inputs before executing the code. Using e.g. -1 will cause a diagnostic error in the CPU and it will stop if you do not have OB121 in place.
Suggestion To thank Quote Answer

12/1/2010 12:10 PM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Thank you, sfa you are very good.... Roby
	Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

12/1/2010 12:47 PM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Sorry, sfa i don't understand why you used the SLD instruction... You want to explain me? Thank you! Roby
	Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

12/1/2010 1:15 PM	Rate (1)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 11/12/2024 Posts: 8768 Rating: (1170)	Dear Roby, The SLD is used to shift the bits 3 times to the left. Because the three least significant bits indicates the bit position. (0 - 7) See also online help of Step 7, search for Pointer and look for format. Hope this will help. Best regards, Wizard

Suggestion To thank Quote Answer

12/1/2010 1:24 PM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Hallo Wizard, how are you? eh, i have never used the pointer whit siemens plc..! Thank you for your explanation bye-bye Roby
	Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

12/2/2010 8:19 PM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Hi, Wizard... where i find the documentation for program pointer explanation? Thank you Roby
	Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

Joined: 9/27/2006

Last visit: 11/12/2024

Posts: 12293

Rating:

(2691)

Hello Roby;
Maybe the explanations in this FAQ might help:
http://support.automation.siemens.com/WW/view/en/20443243

How do you parameterize blocks, which have "ANY"-type or "Pointer" type parameters?

Hope this helps,
Daniel Chartier

12/2/2010 9:41 PM	Rate (0)
Roby Silver Member Joined: 4/10/2006 Last visit: 11/11/2024 Posts: 942 Rating: (2)	Hallo, dchartier than you for your help Roby
	Setting of my PG M6 Siemens OS: Windows 10 Enterprise 22H2; Intel(R) Core(TM) i7-8850H CPU @ 2.60GHz 2.59 GHz - 32G of RAM TIA15.1 Update 8; TIA17 Update 7; TIA18 Update 4 (i use normally)
Suggestion To thank Quote Answer

Share this page:

Share this page on...