Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

6es7841-0cc05-0ya5 is showing in order number

Created by: AutoGen_5669226 at: 10/22/2023 1:01 AM (5 Replies)

Rating (0)

Thanks 0

6 Entries

10/22/2023 1:01 AM	Rate (0)
AutoGen_5669226 Joined: 10/22/2023 Last visit: 10/27/2023 Posts: 4 Rating: (0)	Hello All, As i am new in PLC programming, i was simulating plc programming. There was the error, which says "Module is in operation STOP MODE". When i have run the PLC hardware diagnostic, i have found the CPU order number is differ, which i assigned in HW configuration i.e 6es7841-0cc05-0ya5 is showing in order number, instead of 6ES7 313-5BG04-0AB0. Also there is 3 event which was showing in diagnostic buffer i.e 16#530D, 16#430E & 16#4309. Previously, it was working fine. Can you please help me out on this? Attachment error_2.png (374 Downloads)

Suggestion To thank Quote Answer

10/22/2023 6:37 AM	Rate (0)
ChristophD Grandmaster Joined: 5/12/2006 Last visit: 10/15/2024 Posts: 22414 Rating: (3018)	this is normal if you use PLCSIM have ou try to set the plc to RUN?

Suggestion To thank Quote Answer

10/22/2023 9:58 AM	Rate (0)
AutoGen_5669226 Joined: 10/22/2023 Last visit: 10/27/2023 Posts: 4 Rating: (0)	Hi, Yes i have tried, but there is no LED showing under CPU. (attachement) Attachment error_4.png (337 Downloads)

Suggestion To thank Quote Answer

10/22/2023 3:09 PM	Rate (0)
Hati Platinum Member Joined: 9/21/2012 Last visit: 10/16/2024 Posts: 4181 Rating: (468)	U_fd7abb2e-ab49-4631-bb7c-f222d58bc8d3 Hello All, As i am new in PLC programming, i was simulating plc programming. There was the error, which says "Module is in operation STOP MODE". When i have run the PLC hardware diagnostic, i have found the CPU order number is differ, which i assigned in HW configuration i.e 6es7841-0cc05-0ya5 is showing in order number, instead of 6ES7 313-5BG04-0AB0. Also there is 3 event which was showing in diagnostic buffer i.e 16#530D, 16#430E & 16#4309. Previously, it was working fine. Can you please help me out on this? 6ES7841-0CC05-0YA5 <- S7-PLCSIM V5.4 Floating License 6ES7313-5BG04-0AB0 <- CPU 313C If you have an error in the hardware or software, you will see the error when you compile the hardware and/or software. Do you get any errors in the compiling? If not, then PLsim should work normally.

Suggestion To thank Quote Answer

10/23/2023 6:48 AM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 2/7/2024 Posts: 10533 Rating: (821)	Hello, what about to set correct Access Point (PLCSim) inside PG/PC interface?
	With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

10/23/2023 10:10 AM	Rate (0)
sancruz Gold Member Joined: 3/11/2019 Last visit: 10/15/2024 Posts: 1602 Rating: (293)	Hi, U_fd7abb2e-ab49-4631-bb7c-f222d58bc8d3 Hi, Yes i have tried, but there is no LED showing under CPU. (attachement) This issue was already discussed in this forum for several times. As also the LEDs within PLCSIM are not shown, the cause is the installation of PLCSIM itself. Solution (worked for all other topics): Uninstall PLCSIM (classic) via windows control panel Restart PC Install the latest version of PLCSIM (classic) again. Trial-Software Download für SIMATIC S7-PLCSIM V5.4 SP8 inklusive Updates regards sancruz
	Feedback appreciated, please rate
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on