Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Can not make connection between hmi simulation and plcsim

Created by: madnesssm at: 12/31/2013 1:49 AM (7 Replies)

Rating (1)

Thanks 3

8 Entries

12/31/2013 1:49 AM	Rate (0)
madnesssm Advanced Member Joined: 6/11/2012 Last visit: 10/29/2022 Posts: 30 Rating: (0)	Dear, I am using ET200 IM151-8, IM151-1 and TP700. I have trouble when trying simulate my program. I have instaled plcsim S7 V5.4 and tia portal v12. I can simulate plc via plcsim, but i can not make connection between hmi simulation and plcsim. I tried to change pg/op interface, but still doesn't work. It is interesanting that when everything works fine with S7-1500 sim. Please help
	Last edited by: CS Moderator at: 12/31/2013 5:46 PM new subject after splitting from /tf/WW/en/Posts/94018#top
Suggestion To thank Quote Answer

1/2/2014 10:38 AM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 2/2/2023 Posts: 4177 Rating: (1324)	Hi, I suggest you check first two points: 1 - Acesspoint of application in the connection definition should match with PG/PC interface. 2 - PLC/HMIcommunication definition shoud macht with PLCSim communiction channel i.e: if you define that the HMI will use Ethernet to communicate with PLC, then use PLCSIM(TCP); if STEP7 5.4 communicate with PLCSim ok the Acesspoint of application in the HMIconnection definition should be S7ONLINE.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users Tomy Master HienPhan1995 qwemx

9/9/2015 7:25 AM	Rate (1)
CMJ_control Posts: 1 Rating: (1)	Thanks, I had the same problem. The acces point was called S7ONLINE_1 for some reason.
CMJ_control Posts: 1 Rating: (1)
Suggestion To thank Quote Answer

10/16/2018 8:28 PM	Rate (0)
HienPhan1995 Posts: 1 Rating: (0)	Denilson Pegaia Hi, I suggest you check first two points: 1 - Acesspoint of application in the connection definition should match with PG/PC interface. 2 - PLC/HMIcommunication definition shoud macht with PLCSim communiction channel i.e: if you define that the HMI will use Ethernet to communicate with PLC, then use PLCSIM(TCP); if STEP7 5.4 communicate with PLCSim ok the Acesspoint of application in the HMIconnection definition should be S7ONLINE. Thank you! You're my savior
HienPhan1995 Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

11/1/2022 1:52 PM	Rate (0)
Mirrazabal Regular Member Joined: 4/3/2020 Last visit: 1/31/2023 Posts: 14 Rating: (0)	Good morning! I have the same problem!! When you said that the access point was called S7ONLINE_1 for some reason. Was it in PG/PC configuration? or in Tia portal? Thanks a lot

Suggestion To thank Quote Answer

11/1/2022 2:12 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 2/2/2023 Posts: 21218 Rating: (2797)	it was in tia portal in the hmi connection settings

Suggestion To thank Quote Answer

11/1/2022 3:42 PM	Rate (0)
Mirrazabal Regular Member Joined: 4/3/2020 Last visit: 1/31/2023 Posts: 14 Rating: (0)	ChristophD it was in tia portal in the hmi connection settings Hello Chitophd, Thanks for your answer . I had the connection fine in the hmi configuration. Carrying out different tests, add another HMI to the project and configure it from scratch. I just solved it. I think the problem was that I was using a HW from another project (HMI only). So add another HMI and import popup and it works.

Suggestion To thank Quote Answer

11/4/2022 12:33 PM	Rate (0)
Murof Platinum Expert Joined: 8/3/2009 Last visit: 2/2/2023 Posts: 9695 Rating: (1301)	Hello if you copy an HMI from another project then you should do these steps to get the Communication and configuration work again properly: - Check the IP adresses in the project and correct them as needed - Create a new integrated hmi connection in devices and networks - open connections editor in HMI project. - copy the name of the "old" connection - delete the "old" connection - rename the "new" connection and use the name of the old connection Then compile again everything and existing tags should be connected to new connection and also communication should work Perhaps it helps someone Bye Murof
	If this Information really helps, you could use the Rate function
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

TIA WinCC Communication

Follow us on