Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

CPU555 and ET200U

Created by: gen-a at: 9/23/2019 1:31 PM (8 Replies)

Rating (0)

Thanks 2

9 Entries

9/23/2019 1:31 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	Hi I have toconnect IM(ET 200U-- MLFB : 6ES5318-8MB12) toCP50M1 via Profibus node which will be further processed by CPU 555 of TDC. Also there are some I/O modules like : AO MODULE 6ES5470-8MA12 DI MODULE 6ES5421-8MA12 which will be connected to IM Module. The connection is not established. The processor does not see the station. The CPU551 processor sees the station through the CP50M0 module. Does the CPU555 processor not support ET200U connections?
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

9/23/2019 1:45 PM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (279)	Hello. What errors do you have on the YTS connectors of FB CRV_(P)/CTV_(P) for ET200U? Please also note: Operation of the CPU555 together with a CPU551 is not approved Operation of the CPU555 with the CP5100 and CP50M0 modules that are being phased out is not possible Use of a CP50M1 in combination with a CPU555 is only possible as of a functional status ≥ 4

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users gen-a

9/23/2019 2:27 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	The following errors are present. On CRV 6012, on CTV - 6013. When the ET200U station is connected, the H6 LED on the CP50M1 panel lights up. In hardware, the station is grayed out.
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

9/23/2019 2:30 PM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (279)	6012: The channel is ready. There was no receive operation in this sampling time as the assigned function block is disabled (EN connection). 6013: The channel is ready. There was no transmit operation in this sampling time as the assigned function block is disabled (EN connection) or an incorrect PROFIBUS address has been configured at the slave. Check the EN input of CRV/CTV.

Suggestion To thank Quote Answer

9/23/2019 3:06 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	EN included. CPU 555 does not see hardware et200U station. When you connect a et200m everything works. Only et200U station does not work
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

9/23/2019 3:20 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	The following message is generated:end of the synchronization with a DP master/IO controller on slot2. Number of distributed stations:0. Incoming event.
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

9/24/2019 11:51 AM	Rate (0)
KSN Platinum Expert Joined: 8/25/2006 Last visit: 11/6/2024 Posts: 2211 Rating: (279)	gen-a The following message is generated:end of the synchronization with a DP master/IO controller on slot2. Number of distributed stations:0. Incoming event. Where do you see this message? Can you upload your project here?

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users gen-a

9/24/2019 3:15 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	Attachment HW_config_online.jpg (619 Downloads)
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

9/24/2019 3:16 PM	Rate (0)
gen-a Posts: 6 Rating: (0)	Attachment Error_CP50M1_online.jpg (673 Downloads)
gen-a Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on