Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Error occured while downloading

Created by: azzy9 at: 10/22/2014 3:17 PM (10 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

10/22/2014 3:17 PM	Rate (0)
azzy9 Posts: 93 Rating: (0)	Hello, When I download my project in s120 drive system, it shows an error. Please see the attachment for Error. What are the causes? Help.. Attachment error1.JPG (175 Downloads)
azzy9 Posts: 93 Rating: (0)
Suggestion To thank Quote Answer

10/22/2014 3:25 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/12/2024 Posts: 22446 Rating: (3029)	Hello, can you post the messages from the "target system ouput"? And the faults from the Alarm windows? Regards Christoph

Suggestion To thank Quote Answer

10/22/2014 3:43 PM	Rate (0)
azzy9 Posts: 93 Rating: (0)	Hello, Messages from "Target System Output" are in the attachment. I cannot read alarms while downloading. Im not using drive CLiQ cable on my Single Motor module and also i didnot connected ext. 24v to X21 (3,4) connector of my motor module. Could this be the cause for this error? I guess it is so. Attachment TargetSystem.JPG (159 Downloads)
azzy9 Posts: 93 Rating: (0)
Suggestion To thank Quote Answer

10/22/2014 3:54 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/12/2024 Posts: 22446 Rating: (3029)	Hi, if you cant establish a online connection after the download it can be that there ist a internal system fault is occurred an the CU320 is crashed. How are the LED on the CU320 after download? If you have configured a singel MoMo in the offline topology then you should connect the module via DRIVE-CLiQ before you download this project. Regards Christoph

Suggestion To thank Quote Answer

10/23/2014 7:23 AM	Rate (0)
azzy9 Posts: 93 Rating: (0)	The LED of CU320 is Green. I'm not using the CLiQ cable. Please tell me what is MoMo Topology? I don't understand. After this error, there is online connection.
azzy9 Posts: 93 Rating: (0)
Suggestion To thank Quote Answer

10/23/2014 7:29 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/12/2024 Posts: 22446 Rating: (3029)	Hello, are there faults present after the download in the alarm windows? Unter the CU in the project there is a point "Topology" here you see the Drive CLiQ connections betwenn the CU and the MotorModule, please connect the MotorModule an the CU with a DRIVE CLiQ cable to the ports which are used in the topolgy of the project. regards Christoph

Suggestion To thank Quote Answer

10/23/2014 7:50 AM	Rate (0)
azzy9 Posts: 93 Rating: (0)	P.S. Im not using CLiQ .. Im using normal ethernet cable.
azzy9 Posts: 93 Rating: (0)
Suggestion To thank Quote Answer

10/23/2014 7:58 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/12/2024 Posts: 22446 Rating: (3029)	Hello, No good idea to use a standard ethernet cable insteed of DriveCLiQ. Have you look if any fault is present after the Download with error? regards Christoph
	Last edited by: Min_Moderator at: 10/23/2014 8:59 AM Part splittet to Last edited by: ChristophD at: 10/23/2014 8:05 AM
Suggestion To thank Quote Answer

10/23/2014 8:57 AM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4766 Rating: (122)	New question published byazzy9 is split to a separate thread with the subject Starter v4.4, how to install the HELP. Best regards Min_Moderator

Suggestion To thank Quote Answer

10/23/2014 12:27 PM	Rate (0)
azzy9 Posts: 93 Rating: (0)	Hello, After downloading, the Error (as discused before) occured and after that there is NO ONLINE CONNECTION and RDY LED of CU320 stays Green (not flashing) while all other LEDs are OFF. As for Topology I checked it. Regards, Asad
azzy9 Posts: 93 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on