Navigation

ERROR RUN MODE

Created by: Krnovacek at: 10/30/2016 2:10 PM (7 Replies)

Rating (6)

Thanks 11

8 Entries

10/30/2016 2:10 PM	Rate (0)
Krnovacek Posts: 2 Rating: (0)	HELLO. Please help solve the problems I have. I have purchased software TIA Portal V13 SP1. Furthermore, these modules. CM1241 RS422 / 485 - SIMATIC S7-1200 (CPU1214C DC / DC / DC) - SM1223 DC / RLY. I am trying to run the PLC to RUN mode, but still only illuminates yellow light. If I put FLASH test LED and LED flash. Can you please advise where I wrong? Thank you for your answer. Attachment WEBSERVER.png (569 Downloads)
Krnovacek Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

10/30/2016 3:53 PM	Rate (0)
ChristophD Grandmaster Joined: 5/12/2006 Last visit: 3/20/2023 Posts: 21352 Rating: (2820)	Hello, open the devicediagnosics and then open the diagnostic buffer. Here you get the informatin why the PLC doesn't go to RUN Mode. Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users mindware

10/30/2016 5:03 PM

Rate (0)

Krnovacek

Posts: 2

Rating:

(0)

Number	Local Time	Local Date	Event
1	07:01:32:698 am	1/12/2012	New startup information - Current CPU operating mode: STOP
2	07:01:32:597 am	1/12/2012	System initiated request: - No or no valid data record for central device option handling - CPU changes from STARTUP to STOP mode
3	07:01:32:492 am	1/12/2012	Follow-on operating mode change - CPU changes from STOP to STARTUP mode
4	07:01:32:390 am	1/12/2012	New startup information - Current CPU operating mode: STOP
5	07:01:32:390 am	1/12/2012	Follow-on operating mode change - CPU changes from STOP (initialization) to STOP mode
6	07:01:32:389 am	1/12/2012	Retentive data error: No retentive data - Current CPU operating mode: STOP (initialization)
7	07:01:30:113 am	1/12/2012	Power on - CPU changes from NO POWER to STOP (initialization) mode
8	04:11:27:781 am	1/12/2012	Power off - CPU changes from STOP to NO POWER mode
9	03:50:04:136 am	1/12/2012	New startup information - Current CPU operating mode: STOP
10	03:50:04:035 am	1/12/2012	System initiated request: - No or no valid data record for central device option handling - CPU changes from STARTUP to STOP mode
11	03:50:03:929 am	1/12/2012	Communication initiated request: COLD RESTART - CPU changes from STOP to STARTUP mode
12	03:50:03:929 am	1/12/2012	New startup information - Current CPU operating mode: STOP
13	03:49:59:527 am	1/12/2012	New startup information - Current CPU operating mode: STOP
14	03:49:59:425 am	1/12/2012	System initiated request: - No or no valid data record for central device option handling - CPU changes from STARTUP to STOP mode
15	03:49:59:320 am	1/12/2012	Communication initiated request: COLD RESTART - CPU changes from STOP to STARTUP mode
16	03:49:59:320 am	1/12/2012	New startup information - Current CPU operating mode: STOP
17	03:48:26:789 am	1/12/2012	New startup information - Current CPU operating mode: STOP
18	03:48:26:690 am	1/12/2012	System initiated request: - No or no valid data record for central device option handling - CPU changes from STARTUP to STOP mode
19	03:48:26:586 am	1/12/2012	Follow-on operating mode change - CPU changes from STOP to STARTUP mode
20	03:48:26:483 am	1/12/2012	New startup information - Current CPU operating mode: STOP
21	03:48:26:483 am	1/12/2012	Follow-on operating mode change - CPU changes from STOP (initialization) to STOP mode
22	03:48:26:482 am	1/12/2012	Retentive data error: No retentive data - Current CPU operating mode: STOP (initialization)
23	03:48:24:107 am	1/12/2012	Power on - CPU changes from NO POWER to STOP (initialization) mode
24	03:37:00:192 am	1/12/2012	Power off - CPU changes from STOP to NO POWER mode
25	03:32:08:527 am	1/12/2012	New startup information - Current CPU operating mode: STOP

10/31/2016 9:29 AM	Rate (0)
mopS04 Platinum Expert Joined: 3/5/2014 Last visit: 8/5/2022 Posts: 5521 Rating: (1030)	hi, diagnostic buffer System initiated request: - No or no valid data record for central device option handling - CPU changes from STARTUP to STOP mode is there anything loaded on the CPU? you need to load a valid HW-configuration and a program to the CPU. regards,
	FCK WAR! Be nice!
Suggestion To thank Quote Answer

10/31/2016 9:33 AM	Rate (2)
ChristophD Grandmaster Joined: 5/12/2006 Last visit: 3/20/2023 Posts: 21352 Rating: (2820)	Hi, HW Config should be loaded because the Opton handling is enabled, this is only possible with a loaded HWConfig. But if this Option is active you need a program in the startup to activate a valid data set for Option handling. If you need no option handling deactivate the option in the PLC Porperties and download the Project to the plc. Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 4 thankful Users mopS04 Arasan swowarol Rub Allo

6/28/2021 8:11 AM	Rate (4)
S.Afsar Regular Member Joined: 10/22/2013 Last visit: 10/23/2022 Posts: 8 Rating: (4)	In PLC properties/Configuration control, the tick mark in "Allow to reconfigure the device via the user program" must be removed.

Suggestion To thank Quote Answer
This contribution was helpful to 6 thankful Users Jtrainor abarnaad bertdh AutoGen_4034384 DolaMam Eduardo_SC

1/20/2022 5:15 PM	Rate (0)
bilguun0130.bt@gm... Member Joined: 3/19/2020 Last visit: 3/13/2023 Posts: 1 Rating: (0)	Thank you

Suggestion To thank Quote Answer

2/16/2023 4:50 AM	Rate (0)
Eduardo_SC Joined: 12/28/2022 Last visit: 3/16/2023 Posts: 1 Rating: (0)	S.Afsar In PLC properties/Configuration control, the tick mark in "Allow to reconfigure the device via the user program" must be removed. Thank you so much!!!

Suggestion To thank Quote Answer

Share this page:

Share this page on...

Created by: Krnovacek at: 10/30/2016 2:10 PM (7 Replies)

Rating (6) Thanks 11

8 Entries

Attachment

This contribution was helpful to

This contribution was helpful to

This contribution was helpful to

8 Entries

All about SIMATIC S7-1200

Follow us on

Rating (6)

Thanks 11