Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Not possible to retranslate "softkey cus"?

Created by: Yves_Belgium at: 6/11/2012 7:28 AM (12 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

13 Entries

Entries per page: 10 | all

6/11/2012 7:28 AM	Rate (0)
Yves_Belgium Posts: 23 Rating: (0)	Hi, When i add a cycle to a softkey of my 802d sl control by editing the sc and cov.com files i can not open or retranslate them again to edit my input parametersis this normal? all the rest works fine...
Yves_Belgium Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

6/11/2012 12:48 PM	Rate (0)
Zub04 Bronze Member Joined: 7/15/2009 Last visit: 8/29/2024 Posts: 41 Rating: (1)	After changes in sc.com and cov.com try carry out NC Standart power-up from Start-up and check if you have defined appropriate cycle in CUS with PROC definition. regards

Suggestion To thank Quote Answer

6/11/2012 3:07 PM	Rate (0)
Yves_Belgium Posts: 23 Rating: (0)	Hi thx for the reply and no not even when i perform a restart with power off, this is the program with cov.com and sc.com files, the cycle is defined with "proc" the cycle and input in the program works fine only the retranslation fails (when pressing itstays onthesame line like just typing an iso code and trying to retranslate this code) (also does not give any error) cycle: PROC DYNOFF(INT AHOEK, INT YTRANS, INT ZTRANS) TRANS Y0Z0 L9800 R27=AHOEK R25=YTRANS .... cov.com: ... S5.0.0\$85001\Dynamisch %n Nulpunt Macro: S5.1.0\$85002\DNOF (DYNOFF) "Dyn. Npt %n Rotatie" M17 sc.com: ... //DyNOFF(DYNOFF) (R/-360 360//$85003)[$80021/AHOEK]/B DNOFx (R/-500 500/0/$85004)[$80029/YTRS]/B DNOFy (R/-500 500/0/$85005)[$80025/ZTRS]/B DNOFz M17 seems ok to me or i forget something?
Yves_Belgium Posts: 23 Rating: (0)	Last edited by: Yves_Belgium at: 6/11/2012 3:10 PM Last edited by: Yves_Belgium at: 6/11/2012 3:09 PM
Suggestion To thank Quote Answer

6/12/2012 8:33 AM	Rate (0)
Zub04 Bronze Member Joined: 7/15/2009 Last visit: 8/29/2024 Posts: 41 Rating: (1)	Hi, try this: cov.com: ... S5.0.0\$85001\ S5.1.0\$85002\(DYNOFF) M17 sc.com: ... //(DYNOFF) (I/-360 360//$85003)[$80021/AHOEK]/B DNOFx (I/-500 500/0/$85004)[$80029/YTRS]/B DNOFy (I/-500 500/0/$85005)[$80025/ZTRS]/B DNOFz M17 PROC DYNOFF(INT AHOEK, INT YTRANS, INT ZTRANS) TRANS Y0Z0 L9800 R27=AHOEK R25=YTRANS .... via RCS802 transfer these files to N:CUS and after restart controller if it will not work so try transfer sc.com and cov.com via RCS802 to N:CST and restart. (you had in cycle def int but in mask you had a real) regards

Suggestion To thank Quote Answer

6/12/2012 10:59 AM	Rate (0)
Yves_Belgium Posts: 23 Rating: (0)	Oh yes i go from INT to REAL but even after changing the recompiling won´t happen... i changed cov.com &sc.com, i change the macro and try with defining macro en COV to REAL, evering to INT...only the recompiling won't seems to work maybe has something to do with my SP6? i can also don´t write XML screens in CUSTOM because version is just to old (01.04.01.06 Hotfix)
Yves_Belgium Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

6/12/2012 4:35 PM	Rate (0)
Zub04 Bronze Member Joined: 7/15/2009 Last visit: 8/29/2024 Posts: 41 Rating: (1)	Do you have a version with SP6 (v01.04.06.xx) or do you have v01.04.01.06 (SP1 HF6)? I tested it in version with SP6 and everything worked correct. Now I´m using v01.04.07.04 (SP7 HF4) (Sinumerik 802D sl G/N pro)and it works properly also. XML screens have been also possible since version with SP6.
	Last edited by: Zub04 at: 6/12/2012 4:37 PM
Suggestion To thank Quote Answer

6/12/2012 6:10 PM	Rate (0)
Yves_Belgium Posts: 23 Rating: (0)	Hi Zub, thx for testing! I´ve added my complete version as a PDF in attachment if my version seems to be to old, can i dowload an upgrade somewhere tu run my cycles from COV & SC.com? Regards Attachment 802D sl Pro.pdf (129 Downloads)
Yves_Belgium Posts: 23 Rating: (0)
Suggestion To thank Quote Answer

6/14/2012 8:01 AM	Rate (0)
Zub04 Bronze Member Joined: 7/15/2009 Last visit: 8/29/2024 Posts: 41 Rating: (1)	Hi, yes, it seems to be that you have an old version (sw1.4 SP1 HF6, I suppose that marking of software version is the same for G/N and T/M). I attached screen from my 802. I´m using sw1.4 SP7 HF4. Did you try transfer sc.com and cov.com via RCS802 into CST file also ? This process can help sometimes. (first transfer into CUS then transfer into CST also and finally NCK restart). If you want new software version so you need contact your local siemens for upload. Software upgrades are not available here :(. regards Attachment version.jpg (116 Downloads)

Suggestion To thank Quote Answer

6/14/2012 11:41 PM	Rate (0)
Yves_Belgium Posts: 23 Rating: (0)	Yes i did RCS802 transfers from the 1st time allready and now the last thing i try was to write the macro also in CST, and i also copied the menu code from a drilling cycle and past is in another empty softkey, and this i do can recompile again? Then i change my cycle def in cov en sc to exactly the same as the drillingmenu codeis written and still i can not recompile my code...really strange... Maybe better to leave it like this, it just seems not to work and still i don´t understand what´s the reason. Ididn´t request theprice yet buti think a softwareupgrade by my local Siemens dealer is going to be much to expensive for only recompiling myown writtencycles, for the rest my 802dsl works great... :(
Yves_Belgium Posts: 23 Rating: (0)	Last edited by: Yves_Belgium at: 6/14/2012 11:46 PM
Suggestion To thank Quote Answer

6/15/2012 3:50 PM	Rate (0)
Ekalavya Posts: 2964 Rating: (482)	Yves_Belgium Yes i did RCS802 transfers from the 1st time allready and now the last thing i try was to write the macro also in CST, and i also copied the menu code from a drilling cycle and past is in another empty softkey, and this i do can recompile again? Then i change my cycle def in cov en sc to exactly the same as the drillingmenu codeis written and still i can not recompile my code...really strange... Maybe better to leave it like this, it just seems not to work and still i don´t understand what´s the reason. Ididn´t request theprice yet buti think a softwareupgrade by my local Siemens dealer is going to be much to expensive for only recompiling myown writtencycles, for the rest my 802dsl works great... :( Hello.... Suggestion from my side you can raise Support request to Hotline and get the information. Hope you may have some solutions . Regards, Prakash
Ekalavya Posts: 2964 Rating: (482)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on