Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

problem with hardware uploading

Created by: Qartal at: 2/5/2010 4:07 PM (9 Replies)

Rating (1)

Thanks 5

10 Entries

2/5/2010 4:07 PM	Rate (0)
Qartal Posts: 7 Rating: (0)	Hello, I face with a problem when I try to getting online to CPU 315-2dp (315-2ag10-0ab0-V2.0.8) using Step7 V5.4. I can upload OBs,FBs,FCs,...but when I upload Hardware an error window appears with following content: 2000) error while uploading the the configuration to the programming device (PG). Do you want to continue? and then when I click the help button help on massage 13 : 77 appears Please be informed the CPU is still running without any faults. I have tried to upload hardware with HwConfig too but the same errors taked place. Also I tried to change PG/PC setting but in all correct ones the same error existed. I think it is because of MMC problem. Please help me and if it would be MMC problem then how can recover that.
Qartal Posts: 7 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users LINLIN0514

2/6/2010 10:17 AM	Rate (0)
Raghupathy Posts: 37 Rating: (2)	Hello U hav mentioned that the CPU version V2.08 this is available with ur hardware. Pls check the CPU version available with ur simatic managersoftware from the hardware catalog.Ifit isinferior then update ur hardware catalog by *HW Config > Options > Install HW updates*. Hope this will help u.
Raghupathy Posts: 37 Rating: (2)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Qartal

2/6/2010 10:33 AM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 10/4/2024 Posts: 4515 Rating: (839)	Hello Qartal, Siemens provide with some of its modules configuration CDs. For instance, FM350, FM351, FM355, Siwarex modules,...etc. If one of these modules is installed in a system, and you have uploaded the configuration to a PG whithout installing these configuration software on, then this message will appear. And for sure, you will not be able to modify or configure any thing in the parameters of these modules through the HW configuration. My suggesstion, is to look on the configuration and see if any function/ special modules is available. Then take its MLFB and search in the Support Request for configration software. And then install it befor uploading. I think this will solve your problem. Regards,
	Last edited by: Ayman Elotaify at: 2/6/2010 10:34 AM Ayman Elotaify
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Qartal Med_selmi

2/6/2010 3:45 PM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 10/4/2024 Posts: 10229 Rating: (1181)	Hello, Just to add Which meaning have the error codes (xxxx:yyyy) in STEP 7?(This will be helpful for you in future). best regards, Hristo Mihalev

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Qartal

2/6/2010 8:25 PM	Rate (0)
Qartal Posts: 7 Rating: (0)	Thank you Raghupathy. My Hw catolog is updated. Actually I was updated it yesterday but I cant see V2.0.8 and it appears with V2.0 . I think it is not important thing. do you agree with me?
Qartal Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/6/2010 8:43 PM	Rate (0)
Qartal Posts: 7 Rating: (0)	Dear Umench, I checked the PDF file and found error 13:77 it contains follwing: TEXT : While interpreting the system data blocks (SDBs) uploaded from the module, an error was recognized in the programming device and processing halted. CAUSE : Inconsistent HW configuration in module, occurs when previous loading of SDBs into the module was incomplete or faulty. REMEDY : ?????? Then what I shall do if previous loading of SDBs into the module would be incomplete or faulty? Does exist any way?
Qartal Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/6/2010 9:58 PM	Rate (0)
Qartal Posts: 7 Rating: (0)	Hello , Ayman In this project some standard I/O modules and one VIPA (AC DO) module are directly mounted on rack which have not need to any configuration CD ( I think). Also one Diagnostic Repeater is connected to DP connector of CPU which it utilizes both DP2 and DP3 segments. On these segments there are some ET200s ,some Micromasters and one non siemens nodes. As I know, you cant upload nodes on DP2 and DP3 then it is normal if I cant see nodes. But I cant see the Diagnostic Repeater too. maybe it is because of connection error. I think if uploading error get solved then, the diagnostic repeater will come into view automaticly. Thank you Ayman and I am waiting for you. شكرا لك
Qartal Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

2/7/2010 7:46 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 10/4/2024 Posts: 10229 Rating: (1181)	Hello Qartal, Meanwhile, isn't possible to build new (your) hardware configuration and download it? If you have correct electrical drawings of the project it is possible. And in this way you will find faster remedy of existing issue... Good luck! best regards, Hristo Mihalev

Suggestion To thank Quote Answer

9/18/2013 6:02 PM	Rate (1)
hawas Posts: 2 Rating: (1)	Hello It was a module in step 7 missing, most likely the Drives ES package and it prevents the profibus config from uploading. Hope that can help u
hawas Posts: 2 Rating: (1)
Suggestion To thank Quote Answer

8/13/2018 2:09 PM	Rate (0)
kemitrio Advanced Member Joined: 10/24/2016 Last visit: 8/30/2024 Posts: 6 Rating: (0)	Hello Ihave a system wiht s7 200 and 3 number cp 342 5 . I have 4 number sinamics g120 with cu240E and 2 number et200 that connected on cp 342 When i wanted to uoload ihave same error (2000) and i can not solve it I try to install gsd file for cu240 and cp342 in all version and update hw hardware but problem not solved Can you help me?????

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on