Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S5 928B CPU BASP error, RUN and STOP leds doesn't flash

Created by: Skrytyansky at: 8/27/2023 7:57 AM (10 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

8/27/2023 7:57 AM	Rate (0)
Skrytyansky Joined: 1/6/2023 Last visit: 2/7/2024 Posts: 5 Rating: (0)	Hello! We have a machine controlled S5 928B CPU in our production. Today, the machine stopped, during the diagnostics it turned out the following - the BASP, SI1, SI2 indicators are lit on the CPU, the RUN and STOP indicators are not lit. Tried doing a hard reset, didn't help. We've had similar issues with this CPU before, but then the STOP light was on or blinking. What other actions can be taken? Thank you. Attachment 754ed60a-3339-4e24-b809-aae62009fbf8.jpg (542 Downloads)

Suggestion To thank Quote Answer

8/27/2023 11:44 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/18/2024 Posts: 33783 Rating: (4195)	The manual says this: And this to the LED BASP

Suggestion To thank Quote Answer

8/27/2023 12:09 PM	Rate (0)
Skrytyansky Joined: 1/6/2023 Last visit: 2/7/2024 Posts: 5 Rating: (0)	Yes, thanks, I also found a description of the indicator states in the manual. I don't understand why the CPU doesn't go into stop/run over time or after a hard reset procedure. We found a used CPU and tried to install it, but nothing changed. The only thing is, we don't know if the CPU we found is working.
	Last edited by: Skrytyansky at: 08/27/2023 12:10:33
Suggestion To thank Quote Answer

8/27/2023 2:29 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/18/2024 Posts: 33783 Rating: (4195)	From afar, I can't tell more than what's written in the manual, either. Fact is, the CPU remains in startup and does not go into RUN. Why is that? I don't know it.

Suggestion To thank Quote Answer

8/27/2023 2:40 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/18/2024 Posts: 33783 Rating: (4195)	If you swapped the CPU as a test, you probably also have a PG with STEP 5 or a PC with STEP 5. If so, then read the control bits and the IStack and take screenshots of them. Then upload the screenshots as a ZIP file. Maybe then we can help you.

Suggestion To thank Quote Answer

8/27/2023 5:53 PM	Rate (0)
Skrytyansky Joined: 1/6/2023 Last visit: 2/7/2024 Posts: 5 Rating: (0)	The problem is that I can not connect to the CPU using the programmer. On the CPU itself, indicators SI1 and SI2 are lit, but I understand that this is an error indication, and the connection port is not available.

Suggestion To thank Quote Answer

8/27/2023 6:05 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/18/2024 Posts: 33783 Rating: (4195)	On the photo of the CPU in the first post you can see that something is plugged into the SI1 interface. What is it about? How does the CPU behave when the cable is unplugged?

Suggestion To thank Quote Answer

8/27/2023 6:23 PM	Rate (0)
Skrytyansky Joined: 1/6/2023 Last visit: 2/7/2024 Posts: 5 Rating: (0)	This is the connection between the CPU and the operator panel. I connect the programmer with another cable. If nothing is connected to the connector, then nothing changes. BASP lights up, SI1 and SI2 too, but Stop and Run do not. When I switch to the Online mode in STEP 5, the program displays a PC timeout message. We found two used CPUs and the same story with them. Only, as I said, we do not know if these used CPUs are working.
	Last edited by: Skrytyansky at: 08/27/2023 18:26:40
Suggestion To thank Quote Answer

8/27/2023 6:26 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 9/18/2024 Posts: 33783 Rating: (4195)	Then I think the CPU is defective ...

Suggestion To thank Quote Answer

8/28/2023 6:17 AM	Rate (0)
Skrytyansky Joined: 1/6/2023 Last visit: 2/7/2024 Posts: 5 Rating: (0)	Well, it looks like we've solved the problem. We tried in different ways - we rearranged the microcircuits between all our CPUs, swapped the boards. The actions were fruitless. As a result, I noticed that the CPU board has, well, probably, a tuning capacitor (I'm not strong in the elementary base, but it seems to be it). Unfortunately I can't attach a photo at the moment, but he's the only one there. I rotated it 180 degrees clockwise with the cpu on. And the cpu worked! The stop indicator started flashing, we inserted a eeprom into it, did a full reset and it switched in Run!

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on