Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7-1500 Module State Error

Created by: DaLuckIsRothman at: 9/27/2018 8:51 PM (9 Replies)

Rating (0)

Thanks 1

10 Entries

9/27/2018 8:51 PM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	A S7-1500 CPU at my workplace is showing Module State: Error and Subordinate State : Error. It also show X1 Profinet-Schnittstelle.. all of this error state are shown in the CPU Display. Does this mean that this CPU need to be replaced? If not, then how can I correct this fault. Attachment WhatsApp Image 2018-09-28 at 2.44.26 AM.jpeg (665 Downloads)
	Last edited by: DaLuckIsRothman at: 9/27/2018 8:51:44 PM Last edited by: DaLuckIsRothman at: 9/27/2018 11:35:52 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users titemboldtitem

9/27/2018 8:52 PM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	Attachment WhatsApp Image 2018-09-28 at 2.44.26 AM (1).jpeg (434 Downloads)

Suggestion To thank Quote Answer

9/27/2018 11:56 PM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	If you can see from the image I've attached here, The X1 Profinet point cannot establish online connection, but the X2 Profinet point is just fine. Attachment WhatsApp Image 2018-09-28 at 5.53.31 AM.jpeg (483 Downloads)

Suggestion To thank Quote Answer

9/28/2018 12:13 AM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	This is the ping result, X1 IP address = 192.168.10.2 have no response. X2 IP address = 192.168.60.30 is just fine. Attachment WhatsApp Image 2018-09-28 at 6.10.40 AM.jpeg (346 Downloads)

Suggestion To thank Quote Answer

9/28/2018 12:23 AM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	I've disconnected the X1 Profinet from it's route and plug an internet cable from my laptop directly to X1. I run a ping test and both X1 and X2 point are reachable. Attachment WhatsApp Image 2018-09-28 at 6.19.07 AM.jpeg (309 Downloads)

Suggestion To thank Quote Answer

9/28/2018 12:26 AM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	Still with my laptop plugged in directly to X1. Network view is like the image attached, Highlighted from the CPU S7-1500, it say "OK, difference in lower-level component." I'm running out of option, I will replace the CPU with a new one. Even an hour is critical when you're working in a production. Any experts out there that know how to correct this fault without replacing for a new CPU? Attachment WhatsApp Image 2018-09-28 at 6.19.08 AM.jpeg (339 Downloads)
	Last edited by: DaLuckIsRothman at: 9/28/2018 12:44:42 AM
Suggestion To thank Quote Answer

9/28/2018 7:22 AM	Rate (0)
Hati Platinum Member Joined: 9/21/2012 Last visit: 11/14/2024 Posts: 4199 Rating: (474)	Replacing the CPU is not the answer. You need to see CPU's diagnostic buffer to see the error message list. You already see the text "Error in lower level component", and this means there is a profinet station that has an error in the network.

Suggestion To thank Quote Answer

9/29/2018 4:57 AM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	I've rectified the problem, the reason that I wasn't able to ping X1 was because the monitoring PC and HMI Units are connected through X2. X1 are reserved for drives and encoder. That is why pinging X1 end up in failure. Now the system is running again. Attachment WhatsApp Image 2018-09-29 at 10.53.52 AM.jpeg (333 Downloads)
	Last edited by: DaLuckIsRothman at: 9/29/2018 4:58:09 AM Last edited by: DaLuckIsRothman at: 9/29/2018 4:58:30 AM Last edited by: DaLuckIsRothman at: 9/29/2018 5:03:29 AM
Suggestion To thank Quote Answer

9/29/2018 5:01 AM	Rate (0)
DaLuckIsRothman Member Joined: 8/23/2018 Last visit: 11/19/2020 Posts: 9 Rating: (0)	Like this drive that connected through X1 port, address 192.168.10.100. It is connected properly to the cpu, but when I ping it through the monitoring PC that is connected through X2 port, pinging this address will end up in failure. Attachment WhatsApp Image 2018-09-29 at 10.53.52 AM (1).jpeg (275 Downloads)

Suggestion To thank Quote Answer

10/1/2018 6:12 PM	Rate (0)
0_Einstein Diamond Member Joined: 7/7/2010 Last visit: 11/14/2024 Posts: 15399 Rating: (2443)	If you change the subnet mask for the device connected on X2 and the PLC is allowing ping traffic to route through x2 -> x1, you can ping devices on x1. I do not think ping is a good diagnostic tool for a running system with multiple subnets. TIA Portal diagnostics available right on that display is a great tool that requires no PC to find out what is wrong. DaLuckIsRothman Like this drive that connected through X1 port, address 192.168.10.100. It is connected properly to the cpu, but when I ping it through the monitoring PC that is connected through X2 port, pinging this address will end up in failure.
	science guy
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on