Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S71200 and PC

Created by: gaspar1 at: 9/1/2009 6:36 PM (11 Replies)

Rating (1)

Thanks 2

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

9/1/2009 6:36 PM	Rate (0)
gaspar1 Experienced Member Joined: 1/23/2009 Last visit: 7/20/2024 Posts: 29 Rating: (10)	Hello, today I saw S7-1200 for the first time...I tried to work with him and my first impression is very good...I connect S71200 via PROFINET port with PC for downloading program to PLC. S71200 work great....but later when i try to download program from PLC to PC, I could not find adequate icon for that. I try to do that on these way. I open Step 7 Basic, and i go to Portal view/ Accesible device.When PLC was found by the software, I click on Show in project tree and that work OK, S71200 is online, I can RUN or STOP PLC in online mode, I see on the screen PLC program and all blocks, but I can not download or save program? How to do it? Thank you very much.... Best regards Gaspar
	Be creative while inventing ideas and be disciplined while implementing them... :)
Suggestion To thank Quote Answer

9/2/2009 10:30 AM	Rate (0)
Robster Gold Expert Joined: 5/28/2008 Last visit: 9/11/2024 Posts: 1343 Rating: (141)	Hi, I'm worry about telling you, that uploading program from S7-1200 to PC is at the moment not possible. This week I had the same problem. There is no button and no function of this. But I hope it will be avaible in future. regards

Suggestion To thank Quote Answer

9/2/2009 4:56 PM	Rate (0)
bakerjw Posts: 126 Rating: (18)	There is no upload feature currently in the portal as you would find in the S7-200 or S7-300 programming programs. However. on the left side you can go to online access and update accessible devices. You can copy program blocks from an online PLC into a new project. Kind of a pain but it does work. Hope this helps. John
bakerjw Posts: 126 Rating: (18)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tomy Master

10/8/2009 8:59 PM	Rate (1)
AMPS Posts: 1 Rating: (1)	You can upload a program from the 1200 to your PC. If you compare online/offline you will get an option to upload from the PLC. See the attached. Attachment How to Upload a Program and Configuration from a 1200 PLC.pdf (1164 Downloads)
AMPS Posts: 1 Rating: (1)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Robster

4/16/2010 4:38 AM	Rate (0)
Berg Silver Member Joined: 1/17/2006 Last visit: 8/18/2024 Posts: 553 Rating: (29)	AMPS You can upload a program from the 1200 to your PC. If you compare online/offline you will get an option to upload from the PLC. See the attached. Hello ! I´ve tried to upload the program from PLC how is shown in the PDF tutorial, but it has notworked ! AfterI havedone all 11 steps described in the tutorial, when I go to offline mode and back to online modethe green dot change to blue and orange dots, but opening online and offline I can´t find any differences between offline/online blocks ! Anybody...What´s the problem ?? Greetings.
	"Educate the children and it won't be necessary to punish the men." Pythagoras
Suggestion To thank Quote Answer

4/16/2010 2:12 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 10/4/2024 Posts: 4349 Rating: (1446)	Hi, I don't can imagine what hapens just with this information. Can you send us more informations: Go online, open the tree on the left side.Take a printsreen Open the HW config, online, take other printscreen post them to us.
	Last edited by: Pegaia at: 5/21/2010 12:18 PM Notes: the upload by "detect" function, make a upload of the modules, however without the respectives parameters. Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

10/2/2010 10:12 AM	Rate (0)
ky.novas Posts: 1 Rating: (0)	i will try it.
ky.novas Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

11/4/2010 1:42 AM	Rate (0)
Tyhoon Regular Member Joined: 9/1/2010 Last visit: 6/14/2024 Posts: 27 Rating: (0)	To supply some positive feedback, i followed the procedure and succesfully uploaded the program off the plc. [schnippschnapp] new question is splitted to is there a way to upload off the HMI i have a KTP600 PN?.
	Last edited by: O_Moderator at: 11/8/2010 9:54 AM Last edited by: Tyhoon at: 11/4/2010 1:54 AM
Suggestion To thank Quote Answer

12/8/2010 9:30 PM	Rate (0)
Alvaro Soto Regular Member Joined: 2/1/2008 Last visit: 6/21/2024 Posts: 9 Rating: (0)	I Find the backup option, like other proyects of Wincc Flex, it use Prosave to backup the proyect. You onllyget a encrypted file.

Suggestion To thank Quote Answer

8/9/2011 6:59 PM	Rate (0)
Belittled Posts: 8 Rating: (0)	Helped me out with the same problem, Thanks
Belittled Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on