Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

simo drive triping with fault 608 Speed controller output limited

Created by: moseschaiko at: 1/28/2019 9:12 AM (8 Replies)

Rating (0)

Thanks 2

9 Entries

1/28/2019 9:12 AM	Rate (0)
moseschaiko Posts: 4 Rating: (0)	Hi iam new in this forum would like some help I Have simo drive LT-MODUL INT ,50A IP 6SN1123-1AA00-0CA1 for a cnc machine , it has been triping with fault 608 Speed controller output limited i removed the module opened it and found that the surge arrestor connected in parallel with the DC link terminal flashed I removed the surge arrestor but dont have spare at the time and the machine needs to run Can l fix back the module without the surge arrestor for the time being till i get the spare
moseschaiko Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

1/28/2019 1:57 PM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 12/30/2024 Posts: 4124 Rating: (358)	To help you better, i need you post picture of your drive system. to here surge arrestor connected in parallel To DC bus and I think you have 611U as you said alarm is 608 moseschaiko Hi iam new in this forum would like some help I Have simo drive LT-MODUL INT ,50A IP 6SN1123-1AA00-0CA1 for a cnc machine , it has been triping with fault 608 Speed controller output limited i removed the module opened it and found that the surge arrestor connected in parallel with the DC link terminal flashed I removed the surge arrestor but dont have spare at the time and the machine needs to run Can l fix back the module without the surge arrestor for the time being till i get the spare
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

1/29/2019 10:03 AM	Rate (0)
moseschaiko Posts: 4 Rating: (0)	hi again thanks for your reply have sent you the card image and the surge arrestor removed Again how can i remove alarm 830 tried to use another drive that is ment for x axis movement Attachment IMG_20190128_221227_0.jpg (820 Downloads)
moseschaiko Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

1/29/2019 2:52 PM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 12/30/2024 Posts: 4124 Rating: (358)	#1--I don't support you for open the Siemens drive or power supply cover and doing some thing inside #2--if you still want to discuss, send whole system picture, and if error happen send text not only error # moseschaiko hi again thanks for your reply have sent you the card image and the surge arrestor removed Again how can i remove alarm 830 tried to use another drive that is ment for x axis movement
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

11/22/2019 6:55 PM	Rate (0)
Rejjal Advanced Member Joined: 7/5/2009 Last visit: 6/27/2024 Posts: 76 Rating: (8)	Hi I encountered same problem it was from power board I've contacted with our local Siemens they said that this model (simodrive 611) declined and all parts not available anymore, finally I success to repair damaged board , modules was OK Problem was from one of power board IC, photo attached. Regards Rejjal Attachment IMG_20191117_131442.jpg (942 Downloads)
	You can only go as far as you push
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users vikingman2024

11/22/2019 8:54 PM	Rate (0)
JKV JAMES ❤️(Köni... Silver Member Joined: 12/27/2018 Last visit: 10/2/2024 Posts: 510 Rating: (43)	Hi Refer below link as well. Go to link page
	Jinson James, M.Tech (Power Electronics and Power System),
Suggestion To thank Quote Answer

4/29/2021 5:35 PM	Rate (0)
A.Sal Posts: 1 Rating: (0)	Hi Rejjal, Which IC you replaced, part number or location pls Thanks Rejjal Hi I encountered same problem it was from power board I've contacted with our local Siemens they said that this model (simodrive 611) declined and all parts not available anymore, finally I success to repair damaged board , modules was OK Problem was from one of power board IC, photo attached. Regards Rejjal
A.Sal Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

9/29/2023 1:58 PM	Rate (0)
Rejjal Advanced Member Joined: 7/5/2009 Last visit: 6/27/2024 Posts: 76 Rating: (8)	Hello Sorry for delay, I just see your question it's problem was IGBT single driver ic damaged, photo below In this case it's better to replace gate drive optocoupler ic as well My advice: 1. Make sure that no real overcurrent or block on the motor 2. Swap power module 3. If fault disappeared repair damaged power module Good luck Rejjal Attachment Power module board .jpg (501 Downloads)
	You can only go as far as you push
Suggestion To thank Quote Answer

10/16/2023 9:03 AM	Rate (0)
Jen_Moderator Diamond Member Joined: 6/19/2017 Last visit: 9/6/2024 Posts: 8175 Rating: (173)	Hello Rejjal, thank you for your efforts! Regarding repairs, I have received a recommendation from the Product Management: Product Management We would like to point out that for such a repair, which is carried out independently, is at your own risk. It is advised to contact trained personnel, as always indicated in the manuals, e.g. in the following FAQ in chapter 11 "Spare Parts and Service": Further information regarding SIMODRIVE can be found here: https://support.industry.siemens.com/cs/products?dtp=Manual&mfn=ps&pnid=13259&lc=en-WW Best regards, Jen_Moderator

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Rejjal

|

Share this page:

Share this page on...

Follow us on