Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Sinamics A30042

Created by: Willson90 at: 9/5/2018 8:37 AM (11 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

9/5/2018 8:37 AM	Rate (0)
Willson90 Member Joined: 4/4/2018 Last visit: 12/6/2023 Posts: 5 Rating: (0)	Hi! in our company some of our Sinamics have reached their fan lifetime and the warning A30042 showed up. We have replaced the fan and reset the parameter p251 to 0. But the warning is still active. How can i reset the warning? Greetings

Suggestion To thank Quote Answer

9/5/2018 8:56 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 12/20/2024 Posts: 5974 Rating: (820)	Hello, please have a look at the fault value displayed in brackets A30042 (...) or available in r949 and make sure you have reset the correct value (fan and internal fan). There is an FAQ available which covers this topic. https://support.industry.siemens.com/cs/de/en/view/109480518
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

9/5/2018 9:01 AM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (879)	Please check you have replaced all te fan units of heat sink & power devices fans. Please check the status of r2124 to find out the exact cause of alarm. From it replace the fans & set p0251 & p0254 to zero. Please refer attached sheet for detail information on A30042. Attachment Sinamics S120-A30042.jpg (1076 Downloads)

Suggestion To thank Quote Answer

9/10/2018 9:44 AM	Rate (0)
Willson90 Member Joined: 4/4/2018 Last visit: 12/6/2023 Posts: 5 Rating: (0)	Hi. Sorry for the late reply. Have been trying out your tips just now. But the parameter p254 is not valid,which means i can't reset. I also checked r2124 and the above mentioned r949 but both show me a "0". Is there anything else left i can try to reset the alarm A30042? Thanks for your help! Kind regards.

Suggestion To thank Quote Answer

9/10/2018 2:44 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 12/20/2024 Posts: 5974 Rating: (820)	Hello, sorry for the confusion in the first place r949 is for fault values, r2124 for warning values. Because A30042 is a warning r2124 is the right choice. A30042 doesn`t have a fault value of 0. Please have a look at r2122[x] and the corresponding r2124[x]. For example if r2122[4] shows A30042 r2124[4] provides corresponding the warning code.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

9/12/2018 11:10 AM	Rate (0)
Willson90 Member Joined: 4/4/2018 Last visit: 12/6/2023 Posts: 5 Rating: (0)	Hello, i have checked the parameter you mentioned. In r2122 i see the warning 30042. But how can i reset this? i attached a photo of the parameters (sorry its in german...). The parameter p254 is unknown on our system. Any further suggestions? Attachment rps20180912_110923.jpg (851 Downloads)

Suggestion To thank Quote Answer

9/12/2018 12:24 PM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (879)	Try by setting p0252=0

Suggestion To thank Quote Answer

9/12/2018 2:17 PM	Rate (0)
Willson90 Member Joined: 4/4/2018 Last visit: 12/6/2023 Posts: 5 Rating: (0)	I can not set p252 to 0. As it is the maximum fan lifetime. Any other suggestions?

Suggestion To thank Quote Answer

9/13/2018 10:06 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 12/20/2024 Posts: 5974 Rating: (820)	Hello, please check your access level setting. Parameter p252 is an access level 4 parameter. So you have to activate service level 4 to change the setting of p252 to 0 and back to 40000 again. Have you also performed RAMtoROM and a following PowerOn after setting p251 = 0?
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

9/14/2018 1:02 PM	Rate (0)
Willson90 Member Joined: 4/4/2018 Last visit: 12/6/2023 Posts: 5 Rating: (0)	i have already tried copy from ram to rom. And for access level 4 i need a password which i dont have. Is there any other advice?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_General

Follow us on