Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Transfer data from one Data Block to another

Created by: AlecTek at: 4/6/2011 6:30 PM (5 Replies)

Rating (3)

Thanks 7

6 Entries

4/6/2011 6:30 PM	Rate (0)
AlecTek Posts: 95 Rating: (0)	Does anyone know how to transfer the data from one DB to another?The DBs haveexactly thesame strcture. Thanks
AlecTek Posts: 95 Rating: (0)
Suggestion To thank Quote Answer

4/7/2011 12:35 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 12/8/2023 Posts: 4284 Rating: (1381)	Hi, The MOVE_BLK can be used if your DB is a Array (or if you move arrays inside it). Else, you needuse individual MOVE (or MOVE + MOVE_BLD).
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users AlecTek ravenkore NewGuyOnEarth

4/7/2011 8:50 PM	Rate (0)
AlecTek Posts: 95 Rating: (0)	Its not good........but thank you for the reply
AlecTek Posts: 95 Rating: (0)
Suggestion To thank Quote Answer

4/27/2011 4:48 PM	Rate (3)
Tielenaar Posts: 5 Rating: (3)	Hi, Check your "standard library, system function blocks" after you opened an FC then in STL: CALL SFC20 SRCBLK := P#DBxx.DBXy.z BYTE 20 RET_VAL := MWzz DSTBLK := P#DBoo.DBXp.m BYTE 20 After calling SFC20, the 3 parameters appear automaticly. P# states an any-pointer DBxx.DBXy.z = the start adres of your souce block, BYTE 20 states the length in bytes MWzz = a free MW for diagnostic DBoo.DBXp.m = the start adres of your destination block, BYTE 20 states the length in bytes SFC20 = the standard blockmove instruction which is included in the standard library. Good luck, Tielenaar
Tielenaar Posts: 5 Rating: (3)
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users AlecTek Q121 ravenkore

4/27/2011 7:23 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/9/2023 Posts: 13994 Rating: (2282)	Tielenaar Hi, Check your "standard library, system function blocks" after you opened an FC then in STL: CALL SFC20 SRCBLK := P#DBxx.DBXy.z BYTE 20 RET_VAL := MWzz DSTBLK := P#DBoo.DBXp.m BYTE 20 After calling SFC20, the 3 parameters appear automaticly. P# states an any-pointer DBxx.DBXy.z = the start adres of your souce block, BYTE 20 states the length in bytes MWzz = a free MW for diagnostic DBoo.DBXp.m = the start adres of your destination block, BYTE 20 states the length in bytes SFC20 = the standard blockmove instruction which is included in the standard library. Good luck, Tielenaar That is great for S7-300+, but there is no standard library nor STL for S7-1200 TIA Portal V10.5 Basic SP2.
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users AlecTek

12/14/2017 8:55 AM	Rate (0)
Jen_Moderator Moderator Joined: 6/19/2017 Last visit: 12/7/2023 Posts: 7572 Rating: (156)	New question published by Ajeta is split to a separate thread with the subject Need help for referencing the IO values in the registers. Best regards Jen_Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards Jen_Moderator
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on