Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Compatible or not

Created by: RAJKIRAN at: 10/24/2011 2:05 PM (7 Replies)

Rating (3)

Thanks 5

8 Entries

10/24/2011 2:05 PM	Rate (0)
RAJKIRAN Silver Member Joined: 8/18/2009 Last visit: 6/17/2024 Posts: 548 Rating: (33)	Dear Expert, find attached doc. where X what indicates??? Compatible or not. Attachment M21169 - techno-commercial offer.pdf (488 Downloads)
	Last edited by: RAJKIRAN at: 10/24/2011 2:06 PM Rajkiran Patil
Suggestion To thank Quote Answer

10/24/2011 2:12 PM	Rate (0)
Bilao Posts: 378 Rating: (47)	Hello RAJKIRAN, short and simple--> "x" means compatible. Best regards Bilao
Bilao Posts: 378 Rating: (47)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RAJKIRAN

10/25/2011 7:12 AM	Rate (0)
RAJKIRAN Silver Member Joined: 8/18/2009 Last visit: 6/17/2024 Posts: 548 Rating: (33)	Thanks Bilao, Actually Normal Sign indicate X - Not Applicable √ - Applicable thats for I am confused & no clerify anywhere this in sheet.
	Last edited by: RAJKIRAN at: 10/25/2011 8:48 AM Rajkiran Patil
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users KPawar

10/25/2011 7:20 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 11/1/2024 Posts: 10229 Rating: (1181)	Basically you are right. But you can agree the "X" is much easier to write it there then the other. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

10/25/2011 8:59 AM	Rate (1)
RAJKIRAN Silver Member Joined: 8/18/2009 Last visit: 6/17/2024 Posts: 548 Rating: (33)	Dear Hristo Mihalev, My suggestion that not used this type of sign just easy to write, think about what normal understanding of people(ultimately perpose is used this doc. correctly). or simple Note down at last that "x" means compatible. are you agree with my opinion.
	Rajkiran Patil
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users KPawar

10/25/2011 9:26 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 11/1/2024 Posts: 10229 Rating: (1181)	Dear Rajkiran Patil, Yes, fully agree with you. But to be honest I didn't think in that direction. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

10/26/2011 9:50 AM	Rate (1)
O_Moderator Diamond Member Joined: 4/24/2009 Last visit: 8/20/2024 Posts: 2682 Rating: (135)	Hello together, i forwarded this suggestion to the authors of the compatibility entries. If you want to you can also make a "suggestion for the entry" (see attachment). Best regards O_Moderator Attachment Suggestion for the entry.JPG (445 Downloads)
	Tips&Tricks for the forum usage
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ayman Elotaify

11/25/2011 4:25 PM	Rate (1)
Maulwurf Experienced Member Joined: 5/6/2008 Last visit: 11/18/2024 Posts: 25 Rating: (24)	Hi Rajkiran, there is a new compatibility tool online. You can find the link in the FAQ: http://support.automation.siemens.com/WW/view/en/21927773

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users RAJKIRAN

|

Share this page:

Share this page on...

Follow us on