Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

IE General STOP in Station Configurator

Created by: WernerHimself at: 5/10/2007 10:03 PM (11 Replies)

Rating (1)

Thanks 0

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

5/10/2007 10:03 PM	Rate (0)
WernerHimself Posts: 17 Rating: (2)	Friends, I have a PC using an ethernet card for communication with an S7-400 PLC. In the station configuration editor I add a IE General as I normally do, only this time the RUN/STOP status says STOP. Whatever I change, like IP adresses or index, the STOP does not disappear. A second ethernet card (later added via USB) has the same problem. This card on another PC works fine. Any suggestions?
WernerHimself Posts: 17 Rating: (2)
Suggestion To thank Quote Answer

5/11/2007 7:17 AM	Rate (0)
umencho Grandmaster-Expert Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	Hi, Read this thread:click Best Regards, UMENCHO

Suggestion To thank Quote Answer

5/11/2007 10:41 AM	Rate (0)
WernerHimself Posts: 17 Rating: (2)	Hi Umencho, Thanks for your quick reaction. In the thread you refer to you answer with a step sequence. In step 2 the IE General is placed in configured mode. When I do this at first it seems to work but then it fails. The configuration console says: ----- The module's registration for the configured mode was canceld and it was removed from the Station Configuration Editor. ----- The Station Configuration Editor gives me the following events: ----- Index 1: No valid configuration data found Index 1: The database doens noet contain a system SDB Index 1: Component database invalid A default SDB was created for the proxy with index 1 The CP with index 1 is not operational! Index 1: Componet STOP due to PG command ----- Index 1 is the IE General Any idea?? Thanks in advance.
WernerHimself Posts: 17 Rating: (2)
Suggestion To thank Quote Answer

5/11/2007 11:19 AM	Rate (0)
umencho Grandmaster-Expert Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	Hi, In Station Configurator must change the position of the ethernet card. In INDEX 1 You must put OPC Server, and after that put ethernet card.InpreviouspostInthelinkYoucandownloadtheproject"LOCPRJ"toseethis.

Suggestion To thank Quote Answer

5/11/2007 11:32 AM	Rate (0)
WernerHimself Posts: 17 Rating: (2)	Hi, This does not change anything. Do you have other suggestions? Thanks again.
WernerHimself Posts: 17 Rating: (2)
Suggestion To thank Quote Answer

5/11/2007 12:50 PM	Rate (0)
umencho Grandmaster-Expert Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	Try this: Delete Your S7 project. Delete everything from Station Maneger (OPC Server+IE General). In Configurating Console put for ethernet card not yet configurired. Restart the PC. Download the project from previous post , open in Simatic Manager , rename the PC Station with Your name, In Hardware config change the IP Address. In PG/PC Interface put PCinternal local. In Configuration console for Your card putthatthecardisalreadyconfigurated. In Station Manager put in Index 1 OPC Server, In Index 2 put IE General. Restart the PC. Open the same project and download project.(see the attachment) Best regards UMENCHO Attachment locprj.JPG (1201 Downloads)

Suggestion To thank Quote Answer

5/11/2007 3:21 PM	Rate (0)
WernerHimself Posts: 17 Rating: (2)	Hope you are not getting tired of me.... Still same problem. In Station Configuration Editor I get error after restarting the PC: -------- The CP with index 2 is not operational! Error 0x0320 occured. -------- Any idea what this means: not operational? The ethernet card is working fine. Thanks again
WernerHimself Posts: 17 Rating: (2)
Suggestion To thank Quote Answer

5/12/2007 8:52 AM	Rate (1)
umencho Grandmaster-Expert Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	Hi, See attachment. And something else: When You make project in PG/PC interface you must put PC internal (local). After downloading the project with connection in OPC server and want to see some data with OPC Scout change the PG/PC interface. End when PG/PC interface is PC internal (local) check the diagnostic buffer of the OPC Server for more details about some errors. Best regards umencho Attachment locprj.JPG (1085 Downloads)

Suggestion To thank Quote Answer

5/12/2007 7:43 PM	Rate (0)
Late Platinum Member Joined: 1/7/2006 Last visit: 5/11/2025 Posts: 2705 Rating: (321)	Hi, With the newest SIMATIC NET software that is not necessarry anymore (PC internal).
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

5/13/2007 12:21 AM	Rate (0)
WernerHimself Posts: 17 Rating: (2)	Thanks for your help. The problem still exist but I switch to Profibus, at least that worked within 10 minutes instead of three days without success. Thanks again!
WernerHimself Posts: 17 Rating: (2)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on