Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Sinamic S and SMC 10

Created by: arta_wahyu at: 10/24/2014 2:14 AM (13 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

14 Entries

Entries per page: 10 | all

10/24/2014 2:14 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	Good morning all friend I have SInamic S 120 CU320-2DP + CFC 1 unit SMC 10 2 unit Servo Motor 2 unit TM 31 2 unit Single motor 2 unit Could you tell me how the wiring connection especially for Drive Cliq? also my resolver use DB 9 connector male, and my SMC 10 use DB 25, can you tell use how to convert the DB 9 to DB 25? I mean the terminal connection Thank you for you help and attention Best Regard Arta Wahyu
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/24/2014 2:17 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	Oh ya for single motor I have 6SL3120-1TE21-8AA4 Thank you
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/24/2014 7:38 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/16/2024 Posts: 22356 Rating: (3009)	Hello, which servo motor you have exactly? What so you mean with wiring connection DriveCLiQ? regards Christoph
	Last edited by: ChristophD at: 10/24/2014 7:39 AM
Suggestion To thank Quote Answer

10/25/2014 6:41 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	I want to make connection: CU320-2DP 1 unit Single Motor Module 6SL3121-1TE21-8AA4 2unit SMC 10 2unit TM 31 2unit Servo Motor 1FT6084-8AF71-4BA3-Z 2unit For Line Active Module we don't need because our system has DC link about 531 V and we have also supply 24VDC for CU Please give us the right and clear wiring diagram about connection drive cliq, terminal connection that replace the existing SIMOVERT (DO for drive On,DI for status ready to start,Temperature Motor, AI for analog speed input that represented by voltage from PLC and AI for for analog speed input that represented by current from SIMADIN also please give me the solution about status fault when I try to connect and download from starter. I will attached d the file thank you very much for your help Best Regards Arta Wahyu Attachment example.jpg (156 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 6:42 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	drive cliq connection Attachment Drive Cliq connection.jpg (149 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 6:45 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	this is fault display when I connect CU320-2DP with TM31,Single motor module,SMC 10,Servo Motor Attachment Fault display.jpg (143 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 6:48 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	And I try to ON the drive to On the motor with Starter, but the motor can not be ON, Attachment ON drive Motor.jpg (131 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 6:51 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	status when set parameter single motor at starter Attachment status when set parameter single motor at starter.jpg (137 Downloads)
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 6:52 AM	Rate (0)
arta_wahyu Posts: 30 Rating: (0)	Please give me the solutin about troubleshooting that I ask and at picture I attached Thank you for your help Best Regards Arta Wahyu
arta_wahyu Posts: 30 Rating: (0)
Suggestion To thank Quote Answer

10/25/2014 7:13 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/16/2024 Posts: 22356 Rating: (3009)	Hello, do you have always a project? In the picture "Fault display" it look so. if yes the under the CU is a point "Topology" here you can see the DRIVE-CLiQ wiring of you project. if you open this in online mode you can see the difference between the offline wiring and the online wiring. Other thing is that this motor can't be used with a SMC10! This motor have a incremental encoder and you must use a SMC20, SMC10 is for Resolver encoder! Regards Christoph

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on